AP Physics C: Mechanics · Unit 5 · 10-15% of the exam · about 105 minutes

Unit 5: Torque and Rotational Dynamics

By the end: Describe rotation with angles, angular velocity and angular acceleration, compute torques and rotational inertias (including by integration and the parallel-axis theorem), and use Στ = 0 and Στ = Iα to solve for the forces and motion of rotating systems.

Mr. Thompkins
  1. 5.1 Rotational kinematics · 9 min

    Angles, angular velocity, angular acceleration

    • θ in radians, counterclockwise positive. $\omega = \frac{d\theta}{dt}$, $\alpha = \frac{d\omega}{dt}$.
    • Integrate up the chain with initial conditions: $\omega = \omega_0 + \int\alpha\,dt$, $\theta = \theta_0 + \int\omega\,dt$.
    • Same signs for ω and α: speeding up. Opposite: slowing down.
  2. 5.1 Constant angular acceleration and rotation graphs · 7 min

    When α is constant

    • Constant α only: $\omega = \omega_0 + \alpha t$, $\theta = \theta_0 + \omega_0t + \tfrac{1}{2}\alpha t^2$, $\omega^2 = \omega_0^2 + 2\alpha\Delta\theta$.
    • Slope of ω(t) is α. Area under ω(t) is Δθ.
    • Convert rpm and rev/s with $2\pi$ (and 60 for minutes).
  3. 5.2 Connecting linear and rotational motion · 8 min

    Same ω, different speeds

    • Every point shares θ, ω and α. Linear quantities scale with r.
    • $v = r\omega$, $a_t = r\alpha$, $a_c = r\omega^2$, with angles in radians.
    • Total acceleration of a point: $\sqrt{a_t^2 + a_c^2}$.
  4. 5.3 Torque · 9 min

    What makes things turn

    • $\tau = rF\sin\theta = rF_\perp = r_\perp F$, with θ between $\vec r$ and $\vec F$.
    • The lever arm is the perpendicular distance from the axis to the force's line of action.
    • A force whose line of action passes through the axis gives zero torque.
  5. 5.3 Torque as a cross product, and the torque from gravity · 9 min

    Which way does a torque point?

    • $\vec\tau = \vec r \times \vec F$; for the xy-plane, $\tau_z = xF_y - yF_x$.
    • Positive z (out of the page) is counterclockwise. Order matters.
    • Gravity's torque equals $Mg$ acting at the center of mass.
  6. 5.4 Rotational inertia · 8 min

    Where the mass sits matters

    • $I = \Sigma m_ir_i^2$, with r the perpendicular distance to the axis.
    • I depends on the axis. Mass far from the axis counts the most.
    • I is to rotation what mass is to translation: $\tau = I\alpha$ like $F = ma$.
  7. 5.4 Rotational inertia by integration · 11 min

    Slice it, square it, add it up

    • $I = \int r^2\,dm$: slice so each piece is at one distance r.
    • Rod: $dm = \lambda\,dx$. Disk: rings with $dm = \sigma\,2\pi r\,dr$.
    • Rod about end $\frac{1}{3}ML^2$, about center $\frac{1}{12}ML^2$. Hoop $MR^2$. Disk $\frac{1}{2}MR^2$.
  8. 5.4 The parallel-axis theorem · 8 min

    Moving the axis

    • $I = I_{cm} + Md^2$, d between the center-of-mass axis and a parallel axis.
    • Always start from the center-of-mass axis.
    • The center-of-mass axis gives the smallest I of any parallel axis.
  9. 5.5 Rotational equilibrium and Newton's first law in rotational form · 10 min

    No net force, no net torque

    • Static equilibrium: $\Sigma\vec F = 0$ and $\Sigma\tau = 0$.
    • Zero net torque means constant ω (Newton's first law, rotational form).
    • Choose the pivot where an unknown force acts, so it drops out.
  10. 5.6 Newton's second law in rotational form · 10 min

    Στ = Iα

    • $\Sigma\tau = I\alpha$, with torques and I about the same axis.
    • Only external torques count; the pivot force has no torque about the pivot.
    • If the torque changes with angle or time, α changes: integrate, don't use constant-α equations.
  11. 5.6 Translation and rotation together · 9 min

    Pulleys with mass

    • One $\Sigma F = ma$ per block, one $\Sigma\tau = I\alpha$ per pulley, plus constraints.
    • No slip: $a = R\alpha$. A massive pulley has different tensions; their difference spins it.
    • A disk pulley acts like an extra mass M/2 in the denominator; a hoop like an extra M.
  12. Unit 5 wrap-up · 8 min

    Put it together