AP Physics C: Mechanics · Unit 5 lecture · Part 7 of 12 · 11 min

5.4 Rotational inertia by integrationSlice it, square it, add it up

Mr. Thompkins
For real objects the mass isn't in a few lumps, it's spread out. So the sum becomes an integral: $I = \int r^2\,dm$. The CED expects you to set up and evaluate this integral for rods, hoops, disks and rods whose density changes. One recipe does all of them.

The recipe: (1) Slice the object into pieces that are each, as nearly as possible, all at one distance r from the axis. (2) Write the mass of a slice, dm, using a density: $dm = \lambda\,dx$ for a rod, $dm = \sigma\,dA$ for a flat sheet, $dm = \rho\,dV$ for a solid. (3) Integrate $r^2\,dm$ over the whole object. (4) Use the total mass to replace the density with M.

?Wait, what's linear mass density?
Mass per unit length, $\lambda = \frac{dm}{dx}$, in kg/m. For a uniform rod it's constant, $\lambda = \frac{M}{L}$. If it changes along the rod, $\lambda(x)$ is a function, and the total mass is $M = \int\lambda\,dx$.
axis$dm = \lambda\,dx$$x$$dx$$L$each slice adds $x^2\,dm$
Slice a rod into thin pieces of length dx. Each piece has mass $dm = \lambda\,dx$ and sits at distance x from the axis, so it adds $x^2\,dm$ to I.
A uniform rod, two axes
Derive the rotational inertia of a uniform thin rod (mass M, length L) about a perpendicular axis (a) through one end, and (b) through its center.
  1. Uniform: $\lambda = \frac{M}{L}$, so $dm = \frac{M}{L}dx$, with x measured from the axis.
  2. (a) The rod runs from x = 0 to x = L: $I = \int_0^L x^2\frac{M}{L}dx = \frac{M}{L}\cdot\frac{L^3}{3} = \frac{1}{3}ML^2$.
    Why?
    Write the integral with dm in terms of dx and with limits that match where the axis is. That's the setup point.
  3. (b) Now the rod runs from $x = -\frac{L}{2}$ to $x = +\frac{L}{2}$: $I = \frac{M}{L}\left[\frac{x^3}{3}\right]_{-L/2}^{L/2} = \frac{M}{L}\cdot\frac{2}{3}\cdot\frac{L^3}{8} = \frac{1}{12}ML^2$.
    Why?
    Only the limits changed. Same object, same density, different axis.

Answer: (a) $\frac{1}{3}ML^2$ (b) $\frac{1}{12}ML^2$.

Stuck? Get a hint
  1. $dm = \frac{M}{L}dx$.
  2. About the end, integrate $x^2$ from 0 to L. About the center, from $-L/2$ to $L/2$.
  3. $\int x^2\,dx = \frac{x^3}{3}$.
00.250.50.75100.250.50.751position along rod (units of L)r² (units of L²)axis at end: area 1/3axis at center: area 1/12
Each point's contribution, $r^2$, along a uniform rod. With the axis at the end, the far half contributes a lot (orange area, 1/3). With the axis at the center, no point is more than L/2 away (blue area, 1/12). Same rod, four times the rotational inertia.
Pause and think
About the end, the rod's I is four times its I about the center. Explain that factor of 4 without integrating.
I thought about it. Show me
Think of the rod about its end as two half-rods: about the center, each half reaches out only L/2. About the end, the rod reaches out to L, twice as far, and I scales with distance squared, so $2^2 = 4$. (Check: $\frac{1}{3} \div \frac{1}{12} = 4$.)

Hoops and disks

A thin hoop is the easy one: every bit of its mass is at the same distance R from the central axis, so $I = \int R^2\,dm = R^2\int dm = MR^2$. A solid disk is built from hoops. Slice it into thin rings of radius r and width dr. Each ring's mass is all at distance r.

?Wait, what's area density, and what's the area of a thin ring?
Area density is mass per area, $\sigma = \frac{M}{\pi R^2}$ for a uniform disk. A thin ring of radius r and width dr, unrolled, is almost a strip of length $2\pi r$ and width dr, so its area is $dA = 2\pi r\,dr$ and its mass is $dm = \sigma\,2\pi r\,dr$.
$r$one thin ring:radius r, width dr$dA = 2\pi r\,dr$$dm = \sigma\,2\pi r\,dr$all of it at distance rfrom the axis
A solid disk as a set of thin rings. Each ring is a hoop of radius r: all of its mass is the same distance from the axis.
A solid disk from rings
Derive the rotational inertia of a uniform solid disk (mass M, radius R) about its central axis.
  1. Ring of radius r, width dr: $dm = \sigma(2\pi r\,dr)$ with $\sigma = \frac{M}{\pi R^2}$.
  2. $I = \int_0^R r^2\,dm = \int_0^R r^2\,\frac{M}{\pi R^2}\,2\pi r\,dr = \frac{2M}{R^2}\int_0^R r^3\,dr$.
  3. $= \frac{2M}{R^2}\cdot\frac{R^4}{4} = \frac{1}{2}MR^2$.
    Why?
    Half the hoop's value: the disk has mass at every radius from 0 to R, not all at R. A solid cylinder is a stack of such disks, so it has the same $\tfrac{1}{2}MR^2$ about its long axis.

Answer: $I = \frac{1}{2}MR^2$.

Stuck? Get a hint
  1. Write dm for a ring: $\sigma\cdot 2\pi r\,dr$.
  2. Integrate $r^2\,dm$ from 0 to R; you'll get $r^3$ inside.
  3. Replace σ with $M/(\pi R^2)$ at the end.
A rod that gets heavier
Find the rotational inertia about the pivot end of the tapered rod from section 5: $\lambda = b(1 + x/L)$, M = 1.2 kg, L = 0.90 m.
  1. $I = \int_0^L x^2\,b\left(1 + \frac{x}{L}\right)dx = b\left(\frac{L^3}{3} + \frac{L^3}{4}\right) = \frac{7}{12}bL^3$.
  2. From section 5, $M = \frac{3}{2}bL$, so $b = \frac{2M}{3L}$ and $I = \frac{7}{12}\cdot\frac{2M}{3L}\cdot L^3 = \frac{7}{18}ML^2$.
    Why?
    Always finish in terms of M and L. The exam rarely gives you b.
  3. Numbers: $I = \frac{7}{18}(1.2)(0.90)^2 \approx 0.38\ \text{kg}\cdot\text{m}^2$.
    Why?
    $\frac{7}{18} \approx 0.39$ is bigger than a uniform rod's $\frac{1}{3} \approx 0.33$, because more of the mass sits far from the pivot.

Answer: $I = \frac{7}{18}ML^2 \approx 0.38\ \text{kg}\cdot\text{m}^2$.

Check yourself
A thin rod of length L has density $\lambda = Cx^2$, with x measured from one end. What is its rotational inertia about that end, in terms of its mass M?
  1. A$\frac{1}{3}ML^2$
  2. B$\frac{1}{2}ML^2$
  3. C$\frac{3}{5}ML^2$
  4. D$\frac{3}{4}ML^2$
Show the answer

C. $M = \int_0^L Cx^2\,dx = \frac{CL^3}{3}$ and $I = \int_0^L x^2\cdot Cx^2\,dx = \frac{CL^5}{5}$. Dividing, $\frac{I}{M} = \frac{3L^2}{5}$. Choice A is the uniform rod. Choice B is the answer for $\lambda = Cx$.

Beyond the course, as a bonus: a solid sphere's $\frac{2}{5}MR^2$ comes from stacking thin disks of different radii and integrating their $\tfrac{1}{2}r^2\,dm$. You can use the sphere's value when a problem gives it, but you won't be asked to derive it.

  • $I = \int r^2\,dm$: slice so each piece is at one distance r.
  • Rod: $dm = \lambda\,dx$. Disk: rings with $dm = \sigma\,2\pi r\,dr$.
  • Rod about end $\frac{1}{3}ML^2$, about center $\frac{1}{12}ML^2$. Hoop $MR^2$. Disk $\frac{1}{2}MR^2$.
  • Nonuniform density: find M first, then express the answer in M.