AP Physics C: Mechanics · Unit 5 lecture · Part 8 of 12 · 8 min

5.4 The parallel-axis theoremMoving the axis

Mr. Thompkins
You just integrated a rod about its end and about its center. Do you have to integrate again for every new axis? No. If you know I about the center of mass, one line moves you to any parallel axis.

The parallel-axis theorem: $I = I_{cm} + Md^2$, where $I_{cm}$ is the rotational inertia about an axis through the center of mass, d is the distance between that axis and the new parallel axis, and M is the total mass. Here's why. Measure each piece from the center of mass, at position x'. Its distance from the new axis is $x' + d$, so $I = \int(x' + d)^2\,dm = \int x'^2\,dm + 2d\int x'\,dm + d^2\int dm$. The first term is $I_{cm}$, the last is $Md^2$, and the middle term vanishes.

?Wait, why is $\int x'\,dm$ zero?
Because x' is measured from the center of mass. By definition, $x_{cm} = \frac{1}{M}\int x\,dm$, so measured from the center of mass itself, the mass-weighted average position is zero: the bits on one side balance the bits on the other.
-0.5-0.2500.250.500.10.20.30.4axis distance from center, d (units of L)I (units of ML²)$I = \frac{ML^2}{12} + Md^2$center: 1/12end: 1/3
I of a uniform rod about axes perpendicular to it, at distance d from its center. The curve is a parabola with its lowest point at the center of mass: no parallel axis has a smaller I.
Check the theorem
For the object of section 6 (2.0 kg at each end of a light 1.2 m rod, 1.0 kg at the center), find I about an axis 0.30 m from the center, (a) with the parallel-axis theorem and (b) by direct sum. (c) Check the end axis too.
  1. The center of mass is at the center (the object is symmetric), $I_{cm} = 1.44\ \text{kg}\cdot\text{m}^2$, and M = 5.0 kg.
  2. (a) $I = 1.44 + (5.0)(0.30)^2 = 1.44 + 0.45 = 1.89\ \text{kg}\cdot\text{m}^2$.
  3. (b) Distances from the new axis: 0.30 m (near end), 0.30 m (center), 0.90 m (far end). $I = 2.0(0.30)^2 + 1.0(0.30)^2 + 2.0(0.90)^2 = 0.18 + 0.09 + 1.62 = 1.89\ \text{kg}\cdot\text{m}^2$. They agree.
  4. (c) End axis: $I = 1.44 + (5.0)(0.60)^2 = 3.24\ \text{kg}\cdot\text{m}^2$, matching section 6.

Answer: (a) and (b) both give 1.89 kg·m²; (c) 3.24 kg·m².

Stuck? Get a hint
  1. You need $I_{cm}$, the total mass and d.
  2. $I_{cm} = 1.44$, M = 5.0 kg, d = 0.30 m.
  3. For the direct sum, measure each mass's distance from the new axis.
?Wait, can I just add rotational inertias of different parts?
Yes, as long as every part's I is about the same axis. Rotational inertia is a sum (an integral) over mass, so a rod plus a ball about one pivot is $I_{rod} + I_{ball}$, each computed about that pivot.
A pendulum built from parts
A pendulum is a uniform rod (1.2 kg, 0.80 m) pivoted at its top end, with a solid sphere (2.0 kg, radius 0.10 m) fixed so that its center is 0.90 m below the pivot. Find the pendulum's rotational inertia about the pivot, and compare with treating the sphere as a point mass.
pivotCM of wholerod: 1.2 kg, 0.80 msphere: 2.0 kgradius 0.10 m0.90 m
  1. Rod about its end: $\frac{1}{3}(1.2)(0.80)^2 \approx 0.256\ \text{kg}\cdot\text{m}^2$.
  2. Sphere about the pivot (parallel axis, d = 0.90 m): $\frac{2}{5}(2.0)(0.10)^2 + (2.0)(0.90)^2 = 0.008 + 1.62 = 1.628\ \text{kg}\cdot\text{m}^2$.
    Why?
    The sphere's own $\frac{2}{5}MR^2$ is about its center. The parallel-axis term moves it to the pivot.
  3. Total: $0.256 + 1.628 \approx 1.88\ \text{kg}\cdot\text{m}^2$.
  4. As a point mass, the sphere would give $(2.0)(0.90)^2 = 1.62$, only about 0.5% less than 1.628. A small ball far from the axis is very nearly a point mass.
    Why?
    That's why the simple pendulum model works: the bob's own rotational inertia is tiny compared with $Md^2$.

Answer: About 1.88 kg·m². The sphere's own rotational inertia adds only 0.008 kg·m².

Stuck? Get a hint
  1. Rod about its end: $\frac{1}{3}ML^2$.
  2. Sphere: $\frac{2}{5}MR^2$ about its center, plus $Md^2$ with d = 0.90 m.
  3. Add the two, since both are about the pivot.
Pause and think
Of all the axes parallel to a given direction, which one gives an object its smallest rotational inertia?
I thought about it. Show me
The one through the center of mass, because $Md^2$ can only add. Any other parallel axis has $d > 0$ and a bigger I.
Check yourself
A uniform rod (mass M, length L) rotates about a perpendicular axis through a point L/4 from one end. What is its rotational inertia?
  1. A$\frac{1}{16}ML^2$
  2. B$\frac{7}{48}ML^2$
  3. C$\frac{19}{48}ML^2$
  4. D$\frac{1}{3}ML^2$
Show the answer

B. That point is $\frac{L}{2} - \frac{L}{4} = \frac{L}{4}$ from the center, so $I = \frac{1}{12}ML^2 + M\left(\frac{L}{4}\right)^2 = \frac{4 + 3}{48}ML^2 = \frac{7}{48}ML^2$. Choice C starts from the end value, $\frac{1}{3}ML^2$, and adds $M(L/4)^2$: the theorem only works from the center-of-mass axis.

Exam tip from Mr. T

Write the theorem the same way every time: $I = I_{cm} + Md^2$, then say what d is ("d = distance from the center of mass to the pivot"). Starting from any axis other than the center of mass is the most common way to lose this point.

  • $I = I_{cm} + Md^2$, d between the center-of-mass axis and a parallel axis.
  • Always start from the center-of-mass axis.
  • The center-of-mass axis gives the smallest I of any parallel axis.
  • Add the I of parts about the same axis to get the whole.