AP Physics C: Mechanics · Unit 5 lecture · Part 10 of 12 · 10 min

5.6 Newton's second law in rotational formΣτ = Iα

Mr. Thompkins
Now let the torques not balance. A net torque makes an object's spin change, and how fast it changes depends on the rotational inertia. That's the rotational second law, and it's the engine of the whole unit.

For a rigid object turning about a fixed axis, add $\tau_i = m_ir_i^2\alpha$ over all its pieces (they all share one α): $\Sigma\tau = \left(\Sigma m_ir_i^2\right)\alpha = I\alpha$. Internal forces between pieces come in third-law pairs along the same line, so their torques cancel, and only external torques count. Both sides must be about the same axis.

?Wait, how did I use $\Sigma F = ma$ in Unit 2?
Draw a free-body diagram, choose a positive direction, add the forces with signs, and set the sum equal to ma. The rotational version is the same routine: draw the forces where they act, choose counterclockwise or clockwise as positive, add the torques with signs, and set the sum equal to Iα.
Spinning up a flywheel
A flywheel is a uniform solid disk (8.0 kg, radius 0.25 m) on an axle with a friction torque of 0.50 N·m. A rope pulls tangentially on its rim with a steady 12 N. (a) Find its angular acceleration. (b) How long does it take to reach 50 rad/s from rest?
  1. $I = \frac{1}{2}MR^2 = \frac{1}{2}(8.0)(0.25)^2 = 0.25\ \text{kg}\cdot\text{m}^2$.
  2. Net torque, in the rope's direction: $\Sigma\tau = (0.25)(12) - 0.50 = 3.0 - 0.50 = 2.5\ \text{N}\cdot\text{m}$.
    Why?
    Friction opposes the spin, so its torque gets the opposite sign.
  3. (a) $\alpha = \frac{\Sigma\tau}{I} = \frac{2.5}{0.25} = 10\ \text{rad/s}^2$.
  4. (b) Constant α from rest: $t = \frac{50}{10} = 5.0\ \text{s}$.

Answer: (a) 10 rad/s² (b) 5.0 s.

Stuck? Get a hint
  1. Find I for a solid disk first.
  2. Net torque = rope's torque minus friction's torque.
  3. $\alpha = \Sigma\tau/I$, then $t = \Delta\omega/\alpha$.
pivot$Mg$L/2θ$Mg$(L/2) cos θlever arm of gravityshrinks as it swings
A rod pivoted at one end. Held horizontal, gravity's lever arm is L/2. Once it swings down to angle θ below horizontal, the lever arm is only $(L/2)\cos\theta$.
Pause and think
A uniform rod pivoted at one end is released from horizontal. Is its angular acceleration constant as it swings down?
I thought about it. Show me
No. The torque is $Mg\frac{L}{2}\cos\theta$, which shrinks as the rod swings down, so $\alpha = \frac{3g\cos\theta}{2L}$ shrinks too, reaching zero when the rod hangs straight down. That's why the constant-α equations can't give the rod's speed at the bottom. You'll find it with energy in Unit 6.
The tapered rod drops
The tapered rod from sections 5 and 7 (M = 1.2 kg, L = 0.90 m, $x_{cm} = \frac{5L}{9}$, $I = \frac{7}{18}ML^2$ about the pivot) is held horizontal and released. Find (a) its angular acceleration just after release and (b) the acceleration of its free tip then.
  1. The pivot force acts at the axis, so its torque is zero. Gravity: $\tau = Mg\cdot\frac{5L}{9}$.
  2. (a) $\alpha = \frac{\tau}{I} = \frac{Mg(5L/9)}{(7/18)ML^2} = \frac{10g}{7L} = \frac{10(9.8)}{7(0.90)} \approx 15.6\ \text{rad/s}^2$.
    Why?
    M cancels. Doing the algebra in symbols first, then plugging in, is cleaner and earns the derivation point.
  3. (b) The tip is a distance L from the pivot: $a_t = L\alpha = (0.90)(15.6) \approx 14\ \text{m/s}^2$.
    Why?
    That's more than g. The tip falls faster than a dropped ball, because the rest of the rod, rotating about the pivot, drags it down. A uniform rod's tip does the same: $a = \frac{3}{2}g$.

Answer: (a) $\frac{10g}{7L} \approx 15.6\ \text{rad/s}^2$ (b) about 14 m/s², more than g.

Stuck? Get a hint
  1. Torque: weight times the distance to the center of mass.
  2. $\alpha = \tau/I$; let M cancel.
  3. Tip acceleration: $a_t = L\alpha$.

Finding I in the lab

The Experimental Design and Analysis question likes this setup. Wrap a string around a spool of radius r on a turntable, hang a mass m from it, and measure α with a photogate. The string's tension is $T = m(g - r\alpha)$, so the string's torque is $\tau = m(g - r\alpha)r$. If the bearing has a constant friction torque, $\tau - \tau_f = I\alpha$, so $\tau = I\alpha + \tau_f$. Graph τ against α: the slope is I and the intercept is the friction torque.

00.511.52051015202530α (rad/s²)τ from string (mN·m)best fit: slope 12.0 mN·m per rad/s²intercept: friction
Five trials with hanging masses from 20 g to 100 g on a 2.5 cm spool. The best-fit line has slope 12.0 mN·m per rad/s², which is $0.0120\ \text{kg}\cdot\text{m}^2$, and intercept about 4.0 mN·m.
Read the lab graph
Use the graph. (a) What is the turntable's rotational inertia? (b) What does the vertical intercept mean, and what is its value? (c) A student who ignored friction calculated $I = \tau/\alpha$ from the 20 g trial alone. Would her value be too high or too low?
  1. (a) Slope: from (0, 3.97) to (2.0, 27.94) mN·m, $\frac{27.94 - 3.97}{2.0} \approx 12.0\ \text{mN}\cdot\text{m}$ per rad/s², so $I \approx 0.012\ \text{kg}\cdot\text{m}^2$.
    Why?
    Use points on the best-fit line, far apart, not two data points. Convert mN·m to N·m: divide by 1000.
  2. (b) At α = 0 the string still supplies about 4.0 mN·m. That's the torque needed just to overcome bearing friction: $\tau_f \approx 0.0040\ \text{N}\cdot\text{m}$.
  3. (c) 20 g trial: $\frac{\tau}{\alpha} = \frac{4.90}{0.10} = 49\ \text{mN}\cdot\text{m}$ per rad/s², about 0.049 kg·m², four times too high, because most of that small torque went into friction, not into α.
    Why?
    This is why the graph method is better: the slope separates I from the friction torque.

Answer: (a) about 0.012 kg·m² (b) friction torque, about 0.0040 N·m (c) too high, about 0.049 kg·m².

?Wait, why is the string's tension less than mg?
Because the hanging mass accelerates downward. Its second law: $mg - T = ma$, with $a = r\alpha$ (the string doesn't slip on the spool). So $T = m(g - r\alpha)$, a bit less than mg. Ignoring that makes the torque, and so I, slightly too big.
Check yourself
A wheel with $I = 0.50\ \text{kg}\cdot\text{m}^2$ starts from rest and feels a net torque $\tau(t) = 2.0t$ (N·m, t in seconds). What is its angular velocity at t = 3.0 s?
  1. A6.0 rad/s
  2. B12 rad/s
  3. C18 rad/s
  4. D36 rad/s
Show the answer

C. $\alpha = \frac{\tau}{I} = 4.0t$, so $\omega = \int_0^{3.0}4.0t\,dt = 2.0t^2\big|_0^{3.0} = 18\ \text{rad/s}$. Choice B is $\alpha(3.0)$ in rad/s², and choice D multiplies the final α by the whole time, as if α were constant at its final value.

  • $\Sigma\tau = I\alpha$, with torques and I about the same axis.
  • Only external torques count; the pivot force has no torque about the pivot.
  • If the torque changes with angle or time, α changes: integrate, don't use constant-α equations.
  • Lab: graph τ against α. Slope = I, intercept = friction torque.