AP Physics C: Mechanics · Unit 5 lecture · Part 4 of 12 · 9 min

5.3 TorqueWhat makes things turn

Mr. Thompkins
Try to open a door by pushing right next to the hinges. It barely moves. Push at the handle with the same force and it swings open. Same force, very different result. The quantity that measures turning is called torque, and today you'll see exactly what it depends on.

Torque measures how effectively a force turns an object about an axis. It depends on three things: how big the force is, how far from the axis it acts, and its direction. For a force $F$ applied at a point a distance $r$ from the axis, with angle θ between the position vector $\vec r$ (from the axis to the point) and the force, the torque has size $\tau = rF\sin\theta$. Its unit is the newton-meter.

There are two handy ways to read $rF\sin\theta$. Group $F\sin\theta$: that's $F_\perp$, the part of the force perpendicular to $\vec r$, the only part that turns. Or group $r\sin\theta$: that's $r_\perp$, the lever arm, the perpendicular distance from the axis to the line of action of the force. Both give the same torque: $\tau = rF_\perp = r_\perp F$.

pivot (bolt)$\vec F$ = 80 N60°$r_\perp = r\sin\theta$$r$ = 0.25 mline of action
A wrench 0.25 m long, pulled with 80 N at 60° to the handle. The purple dashed line is the lever arm: the perpendicular distance from the bolt to the line the force acts along.
?Wait, what do sin 0° and sin 90° tell me here?
$\sin 90^\circ = 1$: a force perpendicular to $\vec r$ gives the most torque, $rF$. $\sin 0^\circ = \sin 180^\circ = 0$: a force pointing straight toward or away from the axis gives zero torque, no matter how big it is. In between, $\sin\theta$ tells you what fraction of the force is doing the turning.
Torque on a wrench
You pull on the end of a 0.25 m wrench with 80 N, at 60° to the handle (as in the figure). (a) Find the torque. (b) Find the lever arm. (c) What force, pulled perpendicular to the handle, would give the same torque?
  1. (a) $\tau = rF\sin\theta = (0.25)(80)\sin 60^\circ \approx 17\ \text{N}\cdot\text{m}$.
    Why?
    θ is the angle between $\vec r$ (along the handle, from bolt to hand) and $\vec F$. Using $\cos 60^\circ$ would give 10 N·m.
  2. (b) $r_\perp = r\sin\theta = (0.25)\sin 60^\circ \approx 0.22\ \text{m}$. Check: $r_\perp F = (0.2165)(80) \approx 17\ \text{N}\cdot\text{m}$.
  3. (c) Perpendicular, $\sin\theta = 1$: $F = \frac{\tau}{r} = \frac{17.3}{0.25} \approx 69\ \text{N}$.
    Why?
    A perpendicular pull is the most efficient. Any other angle wastes part of the force pulling along the handle.

Answer: (a) about 17 N·m (b) about 0.22 m (c) about 69 N.

Stuck? Get a hint
  1. $\tau = rF\sin\theta$, with θ between the handle and the force.
  2. $\sin 60^\circ \approx 0.866$.
  3. For (c), set $\sin\theta = 1$ and solve $\tau = rF$ for F.

Adding torques

Several forces on one object give several torques about the same axis. Give each a sign, counterclockwise positive and clockwise negative, and add: $\Sigma\tau = \tau_1 + \tau_2 + \dots$. That net torque is what will decide the angular acceleration, in section 10.

20 N30 N40 N0.50 m0.20 mradial: through the axiscounterclockwise = +
A wheel and axle with three forces. The 20 N force at the rim pushes counterclockwise, the 30 N force on the axle pushes clockwise, and the 40 N force points straight out from the axis.
Net torque from three forces
For the wheel in the figure (rim radius 0.50 m, axle radius 0.20 m), find the net torque about the center. Each force is tangent to its circle except the 40 N force, which is radial.
  1. 20 N at the rim, tangent, turning counterclockwise: $\tau_1 = +(0.50)(20) = +10\ \text{N}\cdot\text{m}$.
  2. 30 N on the axle, tangent, turning clockwise: $\tau_2 = -(0.20)(30) = -6.0\ \text{N}\cdot\text{m}$.
    Why?
    The bigger force gives the smaller torque, because its lever arm is shorter.
  3. 40 N, radial: its line of action passes through the axis, so $\theta = 0$ and $\tau_3 = 0$.
  4. $\Sigma\tau = 10 - 6.0 + 0 = +4.0\ \text{N}\cdot\text{m}$, counterclockwise.

Answer: +4.0 N·m, counterclockwise.

Pause and think
Why are door handles put on the side far from the hinges? And what happens if you push on the edge of the door straight toward the hinges?
I thought about it. Show me
Far from the hinges gives the biggest lever arm, so the same push makes the biggest torque. Pushing straight toward the hinges makes the line of action pass through the axis, so the torque is zero and the door doesn't swing at all, no matter how hard you push.
?Wait, torque is in N·m, and so is work. Is torque a kind of energy?
No. They share units but they're different quantities. Work is force times displacement along the force (a dot product, a scalar measured in joules). Torque is force times a perpendicular distance (a cross product, a vector). Write torque in N·m, never in joules.
Check yourself
Four forces of equal size act on a wheel at its rim. Which one produces zero torque about the axle?
  1. AA force tangent to the rim
  2. BA force at 45° to the radius
  3. CA force pointing straight toward the axle
  4. DA force at 30° to the tangent
Show the answer

C. A force pointing at the axle lies along $\vec r$, so $\theta = 180^\circ$ and $\sin\theta = 0$: its line of action passes through the axis and its lever arm is zero. Every other choice has some perpendicular component. The tangent force gives the most torque.

  • $\tau = rF\sin\theta = rF_\perp = r_\perp F$, with θ between $\vec r$ and $\vec F$.
  • The lever arm is the perpendicular distance from the axis to the force's line of action.
  • A force whose line of action passes through the axis gives zero torque.
  • Sign each torque (counterclockwise +) and add for the net torque.