AP Physics C: E&M · Unit 13 · 10-20% of the exam · about 85 minutes
Unit 13: Electromagnetic Induction
By the end: Calculate magnetic flux and the emf induced by changing it, find the direction of induced currents with Lenz's law, analyze rods and loops moving through fields, and derive and read the behavior of inductors in LR and LC circuits.

- 13.1 Magnetic flux · 8 min
Counting field through a loop
- $\Phi_B = \int \vec B \cdot d\vec A$; flat loop, uniform B: $BA\cos\theta$, θ from the normal. 1 Wb = 1 T·m².
- Face on: BA. Edge on: zero. Turned past 90°: negative.
- Nonuniform B: strips where B is constant, then integrate (beside a wire: $\ln\frac{b}{a}$).
- 13.2 Electromagnetic induction: Faraday's law · 9 min
Change the flux, get an emf
- Faraday: $\varepsilon = -N\frac{d\Phi_B}{dt}$. Only a change in flux induces an emf.
- Three levers: change B, change the area in the field, or change the angle.
- emf against t is minus the slope of the Φ against t graph.
- 13.2 Electromagnetic induction: Lenz's law · 8 min
Nature pushes back
- Lenz: the induced current opposes the change in flux, not the flux.
- Growing flux: induced field opposite. Shrinking flux: induced field the same way.
- Right-hand rule for loops turns the induced field into a current direction.
- 13.3 Induced currents and magnetic forces · 9 min
A rod on rails
- Motional emf: $\varepsilon = B\ell v$ (from Faraday, or from qv × B on the rod's charges).
- Current $\frac{B\ell v}{R}$ feels a drag $\frac{B^2\ell^2v}{R}$ against the motion: magnetic braking.
- Power in = $Fv$ = $I^2R$ = power out.
- 13.3 Induced currents: motion that settles · 9 min
Terminal speed and loops crossing fields
- Falling rod: $m\frac{dv}{dt} = mg - \frac{B^2\ell^2}{R}v$; $v_T = \frac{mgR}{B^2\ell^2}$, $\tau = \frac{mR}{B^2\ell^2}$.
- $v = v_T(1 - e^{-t/\tau})$: starts with acceleration g, levels off at $v_T$.
- A loop crossing a field has an emf only while entering or leaving. Fully inside a uniform field: nothing.
- 13.4 Inductance · 9 min
A coil that resists change
- $L = \frac{N\Phi_B}{I}$ (henries); $\varepsilon_L = -L\frac{dI}{dt}$.
- Long solenoid: $L = \frac{\mu_0 N^2A}{\ell}$, proportional to N².
- Energy: $U_L = \frac{1}{2}LI^2$, stored in the magnetic field.
- 13.5 Circuits with resistors and inductors (LR circuits) · 9 min
Switching on an LR circuit
- The current through an inductor can't jump. No current before: a break just after. Long after: a wire.
- Switching on: $I = \frac{\varepsilon}{R}(1 - e^{-t/\tau})$, $\tau = \frac{L}{R}$; $V_L = \varepsilon e^{-t/\tau}$.
- Initial rate $\frac{dI}{dt} = \frac{\varepsilon}{L}$; final energy $\frac{1}{2}L\left(\frac{\varepsilon}{R}\right)^2$.
- 13.5 LR circuits: switching off and networks · 9 min
Inductors in bigger circuits
- Decay through R: $I = I_0e^{-t/\tau}$, $\tau = \frac{L}{R}$; all $\frac{1}{2}LI_0^2$ becomes heat.
- τ uses the resistance the inductor sees with batteries replaced by wires. Paths can change when switches move.
- Just after a switch, the inductor keeps its old current, even if that takes a large voltage.
- 13.6 Circuits with capacitors and inductors (LC circuits) · 9 min
An electric pendulum
- LC: $\frac{d^2q}{dt^2} = -\frac{1}{LC}q$; $q = Q\cos\omega t$, $\omega = \frac{1}{\sqrt{LC}}$, $T = 2\pi\sqrt{LC}$.
- $i = -\omega Q\sin\omega t$; $I_{max} = \omega Q$. Empty capacitor, largest current.
- Energy is conserved: $\frac{q^2}{2C} + \frac{1}{2}Li^2 = \frac{Q^2}{2C}$.
- Unit 13 wrap-up · 7 min
Put it together