AP Physics C: E&M · Unit 13 lecture · Part 4 of 10 · 9 min

13.3 Induced currents and magnetic forcesA rod on rails

Mr. Thompkins
Time for the free-response favorite: a metal rod sliding along two rails in a magnetic field. It ties together everything: Faraday's law, Lenz's law, the force on a current from Unit 12, and energy conservation. Master this picture and a whole family of exam questions opens up.

A rod of length ℓ slides at speed v along conducting rails joined by a resistor R, in a uniform field B perpendicular to the plane of the rails. The rod, rails and resistor make a loop whose area grows by ℓv every second. So $\frac{d\Phi}{dt} = B\ell v$, and Faraday's law gives the motional emf $\varepsilon = B\ell v$.

?Wait, why does the area grow at ℓv?
The loop is a rectangle of width ℓ (the rod) and length x (from the resistor to the rod). Its area is $A = \ell x$. The rod moves at $v = \frac{dx}{dt}$, so $\frac{dA}{dt} = \ell\frac{dx}{dt} = \ell v$, and with a uniform B, $\frac{d\Phi}{dt} = B\ell v$.

You can also see it from Unit 12. Each charge in the rod moves with the rod, so it feels $q\vec v \times \vec B$, which points along the rod. That force pushes charge toward one end until a current flows around the circuit. Doing the work per charge along the rod gives the same $B\ell v$. Two routes, one answer.

?Wait, what's the force on a current in a field?
$\vec F = I\vec L \times \vec B$, with $\vec L$ along the current. For a straight rod perpendicular to B, the size is $I\ell B$. You found it in Unit 12 by adding up qv × B for all the moving charges.
×××××××××××××××Rrod, length $\ell$$\vec v$I$F_B$flux into the page grows: current counterclockwise
The circuit grows, so the flux into the page grows. The induced current is counterclockwise (up through the rod), and the force IℓB on the rod points left, against the motion.

Now the current is in the rod, and the rod is in the field, so the rod feels a magnetic force $F = I\ell B = \frac{B^2\ell^2v}{R}$. By Lenz's law it points against the motion. This is magnetic braking. To keep the rod moving at constant speed, something must push it with exactly that force. And the power you supply, Fv, equals $\frac{B^2\ell^2v^2}{R} = I^2R$, the power dissipated in the resistor.

Pause and think
If the resistor R is replaced with a larger one, does it get easier or harder to pull the rod at the same speed?
I thought about it. Show me
Easier. The emf Bℓv stays the same, but the current $\frac{B\ell v}{R}$ is smaller, so the magnetic drag $I\ell B$ is smaller. With an open circuit (R infinite) there'd be no current and no drag at all.
Rod on rails
A 0.50 m rod slides at a constant 4.0 m/s on frictionless horizontal rails joined by a 3.0 Ω resistor, in a 0.60 T field into the page, as shown. (a) Find the emf and the current. (b) Find the direction of the current. (c) Find the applied force needed and draw the free-body diagram. (d) Show that energy is conserved.
  1. (a) $\varepsilon = B\ell v = (0.60)(0.50)(4.0) = 1.2$ V. $I = \frac{\varepsilon}{R} = \frac{1.2}{3.0} = 0.40$ A.
  2. (b) Flux into the page is growing, so the induced field points out of the page: the current is counterclockwise, up through the rod and down through the resistor.
    Why?
    Three-step Lenz, out loud. Each link is a rubric point.
  3. (c) $\vec F_B = I\vec\ell \times \vec B$: up the page crossed with into the page: $\hat y \times (-\hat z) = -\hat x$, to the left. Size $(0.40)(0.50)(0.60) = 0.12$ N. Constant velocity means zero net force, so the applied force is 0.12 N to the right.
    Why?
    Constant velocity is not "no force needed". It's "net force zero", and the drag must be balanced.
  4. (d) Power in: $Fv = (0.12)(4.0) = 0.48$ W. Power out: $I^2R = (0.40)^2(3.0) = 0.48$ W. Equal.

Answer: (a) 1.2 V, 0.40 A (b) counterclockwise (c) 0.12 N to the right (d) 0.48 W in and 0.48 W out.

$F_{app}$$F_B = I\ell B$$F_N$$mg$
Free-body diagram of the rod at constant speed: the applied force balances the magnetic drag; gravity and the normal force cancel. No friction: the rails are frictionless.
Stuck? Get a hint
  1. emf = Bℓv, then I = emf/R.
  2. Is the flux into the page growing or shrinking? Then use Lenz.
  3. $F_B$ = IℓB. Constant speed: $F_{app}$ equals $F_B$.
Check yourself
The rod above is pulled at twice the speed, 8.0 m/s. By what factor does the power dissipated in the resistor change?
  1. A4
  2. B2
  3. C1
  4. D8
Show the answer

A. The emf and current double, so $I^2R$ goes up by 4 (and so does Fv: twice the force at twice the speed). The trap is 2, which only counts the larger current or the larger speed.

  • Motional emf: $\varepsilon = B\ell v$ (from Faraday, or from qv × B on the rod's charges).
  • Current $\frac{B\ell v}{R}$ feels a drag $\frac{B^2\ell^2v}{R}$ against the motion: magnetic braking.
  • Power in = $Fv$ = $I^2R$ = power out.
  • Find the current direction with Lenz, then check the force direction with IL × B.