AP Physics C: E&M · Unit 13 lecture · Part 8 of 10 · 9 min

13.5 LR circuits: switching off and networksInductors in bigger circuits

Mr. Thompkins
Ever seen a spark jump when someone yanks a plug out of a running motor? That's an inductor refusing to let its current stop. Let's handle switching off, and inductors buried inside bigger circuits.

Switching off. If an inductor carrying current $I_0$ is given a path through a resistor R (and no battery), the loop rule is $-IR - L\frac{dI}{dt} = 0$, so $\frac{dI}{dt} = -\frac{R}{L}I$ and $I = I_0e^{-t/\tau}$ with $\tau = \frac{L}{R}$. The inductor's stored energy $\frac{1}{2}LI_0^2$ ends up as heat in the resistor. If instead the circuit is simply broken, the inductor tries to keep the current going and its voltage spikes, often enough to spark across the gap.

?Wait, how did we find τ for a capacitor buried in a network?
Replace each ideal battery with a wire, then find the equivalent resistance looking out from the capacitor's two terminals. The same rule works for an inductor: τ = L divided by the resistance the inductor sees.
20 VS$R_1 = 5.0\ \Omega$$R_2 = 20\ \Omega$2.0 H
R₁ in series with the battery and switch, then R₂ in parallel with the inductor.
MomentCurrent through LVoltage across LTreat L as
Just after a switch (no current before)Zero, as beforeWhatever the circuit needsA break in the wire
Just after a switch (current I₀ before)Still I₀Whatever keeps I₀ flowingA current source, for an instant
Long afterSteadyZeroA plain wire
Compare: capacitorIts voltage never jumpsEmpty at first: a wireLong after: a break
The inductor's rules at each moment, with the capacitor's for comparison.
An inductor in parallel
In the circuit shown, the switch has been open a long time and closes at t = 0. Find (a) the battery current and the inductor's voltage just after closing, (b) the battery current long after, and (c) the time constant. (d) Long after, the switch is opened again. Find the voltage across $R_2$ just after opening, the new time constant, and the total heat produced in $R_2$.
  1. (a) Just after closing, the inductor's current is still zero: it acts like a break. $R_1$ and $R_2$ are in series: $I = \frac{20}{5.0 + 20} = 0.80$ A. The inductor is in parallel with $R_2$, so it has $R_2$'s voltage: $(0.80)(20) = 16$ V.
    Why?
    "Acts like a break" means you solve the circuit with that branch removed. The inductor still has a voltage across it: whatever its parallel partner has.
  2. (b) Long after, the inductor is a wire and shorts $R_2$: $I = \frac{20}{5.0} = 4.0$ A, all of it through the inductor.
  3. (c) Looking out from the inductor with the battery as a wire, $R_1$ and $R_2$ are in parallel: $\frac{(5.0)(20)}{25} = 4.0\ \Omega$. $\tau = \frac{2.0}{4.0} = 0.50$ s.
  4. (d) Opening the switch cuts off the battery and $R_1$. The inductor keeps its 4.0 A for an instant, and the only path is through $R_2$: $V = (4.0)(20) = 80$ V, four times the battery voltage.
    Why?
    Nothing says a voltage can't exceed the battery's. The inductor will drive whatever voltage it takes to keep its current from jumping.
  5. The current then decays through $R_2$ alone: $\tau = \frac{L}{R_2} = \frac{2.0}{20} = 0.10$ s. All the stored energy becomes heat in $R_2$: $\frac{1}{2}LI^2 = \frac{1}{2}(2.0)(4.0)^2 = 16$ J.

Answer: (a) 0.80 A, 16 V (b) 4.0 A (c) 0.50 s (d) 80 V across $R_2$, τ = 0.10 s, 16 J of heat.

Stuck? Get a hint
  1. Just after closing: the inductor branch carries no current. Remove it and solve.
  2. Long after: the inductor is a wire across R₂.
  3. After opening: the inductor's 4.0 A has only one path, through R₂.
00.10.20.30.40.5012345t after opening (s)I (A)37% at τ = 0.10 s
After the switch opens, the inductor's current dies away through R₂ alone, with τ = L/R₂ = 0.10 s.
Pause and think
Just after the switch opens in the walk above, which way does the current flow through $R_2$, compared with before?
I thought about it. Show me
Up through $R_2$. Long after closing, $R_2$ carried no current at all, because the inductor shorted it. Just after opening, the inductor's 4.0 A keeps flowing down through the inductor, and the only way back around is up through $R_2$. So $R_2$'s current jumps from 0 to 4.0 A, flowing up, opposite to the 0.80 A that flowed down through it just after the switch first closed.
?Wait, why does R₂ carry no current long after closing?
The ideal inductor is a wire in parallel with $R_2$. A wire has no voltage across it, so $R_2$, connected to the same two points, has no voltage either, and no current. Everything goes through the wire-like inductor.
Check yourself
An inductor carrying a steady 2.0 A begins to discharge through a resistor, with τ = 0.30 s. What is the current 0.60 s later?
  1. A0.27 A
  2. B0.74 A
  3. C1.0 A
  4. D0.50 A
Show the answer

A. $I = 2.0e^{-0.60/0.30} = 2.0e^{-2} = 0.27$ A. Choice B is one time constant, $2.0e^{-1}$. Choice D halves twice, but two time constants is not two half-lives.

Exam tip from Mr. T

When you sketch an inductor current, mark the starting value, draw the asymptote dashed, and mark the 63% (rising) or 37% (falling) point at t = τ. A smooth curve, concave the right way, that never crosses its asymptote earns the shape point.

  • Decay through R: $I = I_0e^{-t/\tau}$, $\tau = \frac{L}{R}$; all $\frac{1}{2}LI_0^2$ becomes heat.
  • τ uses the resistance the inductor sees with batteries replaced by wires. Paths can change when switches move.
  • Just after a switch, the inductor keeps its old current, even if that takes a large voltage.
  • Opening a circuit with an inductor can make a voltage far above the battery's.