AP Physics C: E&M · Unit 13 lecture · Part 7 of 10 · 9 min

13.5 Circuits with resistors and inductors (LR circuits)Switching on an LR circuit

Mr. Thompkins
Put an inductor in a circuit with a battery and a resistor and close the switch. In Unit 11, the capacitor's voltage couldn't jump. Here the inductor's current can't jump. Watch how much of Unit 11 carries straight over.

Because $\varepsilon_L = -L\frac{dI}{dt}$, an instant jump in current would need an infinite emf. So the current through an inductor can't change suddenly. If it was zero before the switch closed, it's zero just after: at that instant the inductor acts like a break in the wire, and the whole battery voltage appears across it. Long after, the current is steady, $\frac{dI}{dt} = 0$, the inductor has no voltage, and it acts like a plain wire.

?Wait, which element acted like a wire at first in Unit 11?
The empty capacitor: it had no voltage, so just after the switch it acted like a wire, and long after, full, it acted like a break. The inductor is the reverse: a break at first, a wire long after.
24 VS$8.0\ \Omega$2.0 HIswitch closes at t = 0
A series LR circuit. Walking clockwise after the switch closes: +ε across the battery, −IR across the resistor, −L dI/dt across the inductor.
Derive I(t), then use it
In the circuit shown (ε = 24 V, R = 8.0 Ω, L = 2.0 H), the switch closes at t = 0. (a) Derive I(t) from the loop rule. (b) Find the time constant, the final current and the initial rate dI/dt. (c) Find the current at t = 0.50 s. (d) Find the energy stored in the inductor long after.
  1. (a) Loop rule: $\varepsilon - IR - L\frac{dI}{dt} = 0$, so $\frac{dI}{dt} = \frac{R}{L}\left(\frac{\varepsilon}{R} - I\right)$.
    Why?
    The inductor term is the voltage drop $L\frac{dI}{dt}$ in the direction of a rising current. Label every term.
  2. Separate and integrate from I = 0 at t = 0: $\int_0^I \frac{dI'}{\varepsilon/R - I'} = \int_0^t \frac{R}{L}dt'$, so $-\ln\frac{\varepsilon/R - I}{\varepsilon/R} = \frac{Rt}{L}$ and $I = \frac{\varepsilon}{R}\left(1 - e^{-Rt/L}\right)$.
  3. Check: I(0) = 0 (a break at first) and $I(\infty) = \frac{\varepsilon}{R}$ (a wire long after). Both match.
    Why?
    Saying that you checked both limits is often a point by itself.
  4. (b) $\tau = \frac{L}{R} = \frac{2.0}{8.0} = 0.25$ s. $I_{final} = \frac{24}{8.0} = 3.0$ A. At t = 0, I = 0, so $L\frac{dI}{dt} = \varepsilon$ and $\frac{dI}{dt} = \frac{24}{2.0} = 12$ A/s.
    Why?
    Consistency check: the starting slope times τ should equal the final current. $(12)(0.25) = 3.0$ A. It does.
  5. (c) $I(0.50) = 3.0(1 - e^{-2}) = 2.6$ A.
  6. (d) $U = \frac{1}{2}LI^2 = \frac{1}{2}(2.0)(3.0)^2 = 9.0$ J.

Answer: (a) $I = \frac{\varepsilon}{R}(1 - e^{-Rt/L})$ (b) τ = 0.25 s, 3.0 A, 12 A/s (c) 2.6 A (d) 9.0 J.

Stuck? Get a hint
  1. Loop rule with three terms: ε, −IR, −L dI/dt.
  2. Separate: dI/(ε/R − I) = (R/L) dt.
  3. τ = L/R, not LR. Final current: the inductor is a wire, so ε/R.
00.250.50.7511.2500.511.522.533.5t (s)I (A)ε/R = 3.0 A63% at τ
The current climbs to ε/R = 3.0 A, reaching 63% at t = τ = 0.25 s.
00.250.50.7511.250481216202428t (s)$V_L$ (V)37% at τ
The inductor's voltage starts at the full 24 V and decays to zero; at every instant it plus IR equals 24 V.
?Wait, why is the time constant L/R and not LR?
Check the units. A henry is a V·s/A and an ohm is a V/A, so $\frac{L}{R}$ comes out in seconds. LR would be in V²·s/A². Physically: a bigger L resists change more (slower), a bigger R makes the final current smaller so it's reached sooner (faster).
Pause and think
At the instant the current is half its final value, what fraction of the battery voltage is across the inductor?
I thought about it. Show me
Half. The resistor has $IR = \frac{1}{2}\varepsilon$, and the loop rule says the rest, $\frac{1}{2}\varepsilon$, is across the inductor. That happens at $t = \tau\ln 2 = 0.17$ s here.
Check yourself
In a series LR circuit with a battery, what is the voltage across the resistor immediately after the switch is closed?
  1. AZero
  2. Bε
  3. Cε/2
  4. DεR/L
Show the answer

A. Just after closing, the inductor holds the current at zero, so $IR = 0$ and the full ε sits across the inductor. The trap is ε, which belongs to the long-time limit.

  • The current through an inductor can't jump. No current before: a break just after. Long after: a wire.
  • Switching on: $I = \frac{\varepsilon}{R}(1 - e^{-t/\tau})$, $\tau = \frac{L}{R}$; $V_L = \varepsilon e^{-t/\tau}$.
  • Initial rate $\frac{dI}{dt} = \frac{\varepsilon}{L}$; final energy $\frac{1}{2}L\left(\frac{\varepsilon}{R}\right)^2$.