AP Physics C: E&M · Unit 13 lecture · Part 1 of 10 · 8 min

13.1 Magnetic fluxCounting field through a loop

By the end: Calculate magnetic flux and the emf induced by changing it, find the direction of induced currents with Lenz's law, analyze rods and loops moving through fields, and derive and read the behavior of inductors in LR and LC circuits.
Mr. Thompkins
Welcome to the last unit, and maybe the most useful one. Every power plant, guitar pickup, wireless charger and induction stove runs on one idea: change the magnetic field through a loop and a voltage appears. Before we can change it, we need a way to measure how much field goes through a loop. That's flux.

Magnetic flux measures how much magnetic field passes through a surface. For a small flat piece of area $dA$, define $d\vec A$ as a vector of size dA pointing along the normal, perpendicular to the surface. Then $d\Phi_B = \vec B \cdot d\vec A$, and for the whole surface $\Phi_B = \int \vec B \cdot d\vec A$. The unit is the weber: 1 Wb = 1 T·m².

?Wait, what's a dot product again?
$\vec A \cdot \vec B = AB\cos\theta$, where θ is the angle between the two vectors. It picks out how much of one vector points along the other. It's largest when they're parallel, zero when they're perpendicular, and negative when they point more than 90° apart.

For a flat loop of area A in a uniform field, the integral becomes $\Phi_B = BA\cos\theta$, where θ is the angle between $\vec B$ and the loop's normal. Face on (θ = 0), all the field goes through: Φ = BA. Edge on (θ = 90°), none does: Φ = 0, however strong the field. Turn the loop past 90° and the flux goes negative, because the field now passes through it the other way.

Bloop, edge onnormal $\hat n$θ$\Phi_B = BA\cos\theta$, θ measured from the normal
Only the part of B along the normal threads the loop. Tilting the loop changes the flux without changing B or A.
0306090120150180-1.2-0.8-0.400.40.81.21.6θ, angle between B and the normal (degrees)$\Phi_B / BA$face on: BAedge on: 0flipped: −BA
Flux through a flat loop in a uniform field, as a fraction of BA, against the angle from the normal.
Pause and think
A problem says "the field makes 30° with the plane of the loop." Is that θ in $BA\cos\theta$?
I thought about it. Show me
No. θ is measured from the normal, which is 90° away from the plane. So θ = 60°, and $\Phi = BA\cos 60° = BA\sin 30°$. Reading the angle from the plane is one of the most common slips in this unit.

One more fact. Through any closed surface the net magnetic flux is zero, $\oint \vec B \cdot d\vec A = 0$, because magnetic field lines are closed loops: every line that goes in comes out. That's Gauss's law for magnetism, and it's the "no monopoles" fact from Unit 12 written as an equation.

?Wait, what did Gauss's law for electricity say?
$\oint \vec E \cdot d\vec A = \frac{q_{enc}}{\varepsilon_0}$. Electric flux out of a closed surface measures the charge inside. The magnetic version has zero on the right, because there is no magnetic charge to enclose.

When B varies across the loop

If the field changes from place to place over the loop, you can't just multiply. Slice the loop into strips on which B is constant, find each strip's flux, and integrate. The classic case is a rectangle next to a long straight wire, where $B = \frac{\mu_0 I}{2\pi r}$ depends on the distance r from the wire.

Flux beside a long wire
A long straight wire carries 15 A. A rectangular loop lies in the same plane, with its 0.30 m sides parallel to the wire. Its near side is 2.0 cm from the wire and its far side 8.0 cm. (a) Derive the flux through the loop. (b) Evaluate it. (c) If the current rises at 200 A/s, find the emf around the loop (you'll meet Faraday's law in the next section, but try it).
I×××××××××××××××rdr2.0 cm8.0 cm0.30 m
A strip of width dr at distance r from the wire. On it the field (into the page, for this current) has one value.
  1. (a) Use strips parallel to the wire, at distance r and width dr. On a strip B is constant, $B = \frac{\mu_0 I}{2\pi r}$, and the strip's area is $dA = (0.30)\,dr$. The field is perpendicular to the loop, so $d\Phi = B\,dA$.
    Why?
    Choose strips along which B doesn't change. Here that means strips parallel to the wire.
  2. $\Phi = \int_a^b \frac{\mu_0 I}{2\pi r}(0.30)\,dr = \frac{\mu_0 I(0.30)}{2\pi}\ln\frac{b}{a}$.
  3. (b) $\ln\frac{8.0}{2.0} = \ln 4 = 1.386$. $\Phi = (2 \times 10^{-7})(15)(0.30)(1.386) = 1.2 \times 10^{-6}$ Wb.
    Why?
    $\frac{\mu_0}{2\pi} = 2 \times 10^{-7}$ T·m/A. Only the ratio of the distances matters, so centimeters are fine inside the log.
  4. (c) Everything but I is fixed, so $|\varepsilon| = \frac{d\Phi}{dt} = \frac{\mu_0(0.30)\ln 4}{2\pi}\frac{dI}{dt} = (8.3 \times 10^{-8})(200) = 1.7 \times 10^{-5}$ V.

Answer: (a) $\Phi = \frac{\mu_0 I\ell}{2\pi}\ln\frac{b}{a}$ (b) $1.2 \times 10^{-6}$ Wb (c) $1.7 \times 10^{-5}$ V.

Stuck? Get a hint
  1. B depends on r, so you need strips at constant r.
  2. Each strip: dΦ = (μ₀I/2πr)(0.30 m) dr.
  3. Integrate dr/r from 2.0 cm to 8.0 cm: that gives ln 4.
Check yourself
A flat loop of area 0.020 m² sits in a uniform 0.60 T field that makes an angle of 30° with the plane of the loop. What is the flux?
  1. A0.0060 Wb
  2. B0.010 Wb
  3. C0.012 Wb
  4. DZero
Show the answer

A. The angle from the normal is 60°: $\Phi = (0.60)(0.020)\cos 60° = 0.0060$ Wb. Choice B uses cos 30°, the angle from the plane. Choice C ignores the angle.

  • $\Phi_B = \int \vec B \cdot d\vec A$; flat loop, uniform B: $BA\cos\theta$, θ from the normal. 1 Wb = 1 T·m².
  • Face on: BA. Edge on: zero. Turned past 90°: negative.
  • Nonuniform B: strips where B is constant, then integrate (beside a wire: $\ln\frac{b}{a}$).
  • Net flux through any closed surface is zero: no monopoles.