AP Physics C: E&M · Unit 11 lecture · Part 4 of 11 · 7 min

11.4 Electric powerWhere the energy goes

Mr. Thompkins
Electric companies don't sell you electrons. You give every one of them back. What they sell is energy. Let's track it: where the battery puts it in, and where the resistors take it out.

A charge dq that drops through a potential difference ΔV loses potential energy $dU = dq\,\Delta V$. Divide by dt and you get the rate: $P = \frac{dU}{dt} = I\Delta V$. Power is in watts, joules per second. For a battery, $P = I\varepsilon$ is the rate it supplies energy. For a resistor, $I\Delta V$ is the rate it turns electrical energy into thermal energy (and light, for a bulb).

?Wait, what's power in mechanics?
Power is the rate of doing work or transferring energy: $P = \frac{dW}{dt}$, in watts. A 60 W bulb transfers 60 joules every second. The total energy over a time is $E = \int P\,dt$, which is $Pt$ when P is constant.
?Wait, what's Ohm's law again?
For an ohmic resistor, the current is proportional to the voltage across it: $\Delta V = IR$ with R constant. Any two of ΔV, I and R give the third: $I = \frac{\Delta V}{R}$, $R = \frac{\Delta V}{I}$.

Combine with Ohm's law and a resistor's power has three forms: $P = I\Delta V = I^2R = \frac{(\Delta V)^2}{R}$. They're the same physics, but pick the one built on what's shared. In series the current is the same, so $I^2R$ says the bigger resistor gets more power. In parallel the voltage is the same, so $\frac{(\Delta V)^2}{R}$ says the smaller resistor gets more power. And energy is conserved: the total power the batteries deliver equals the total power all the resistors use.

FormBest whenSays
$P = I\Delta V$Any element: battery, resistor, motorEnergy per charge times charge per second
$P = I^2R$Resistors in series (same I)In series, bigger R uses more power
$P = \frac{(\Delta V)^2}{R}$Resistors in parallel (same ΔV)In parallel, smaller R uses more power
Three forms of resistor power. Choose by what the resistors share.

Bulb brightness follows power, not current or voltage alone. That's the key to every "which bulb is brighter" question. Here's a famous one. A 60 W bulb and a 100 W bulb are both rated for 120 V: that's the power each uses when it has 120 V across it. From $P = \frac{(\Delta V)^2}{R}$, the 60 W bulb has $R = \frac{120^2}{60} = 240\ \Omega$ and the 100 W bulb has $R = 144\ \Omega$. The dimmer bulb has the bigger resistance.

Pause and think
Now put those two bulbs in series across 120 V. Which one glows brighter? Treat their resistances as fixed.
I thought about it. Show me
The 60 W bulb. In series both carry the same current, and $P = I^2R$ gives more power to the larger resistance, which is the 60 W bulb (240 Ω). The label tells you power at 120 V, not power in every circuit.
Rated bulbs in series
The 60 W and 100 W bulbs (240 Ω and 144 Ω, treated as fixed) are connected in series across 120 V. Find (a) the current, (b) the power in each bulb, and (c) the total power, and compare it with the 160 W they use in parallel.
Parallel, 120 V6060 W bulb100100 W bulbSeries, 120 V23 W60 W bulb14 W100 W bulb
Same two bulbs, same 120 V. In parallel each gets its rated power. In series the 60 W bulb is the brighter one, and both are much dimmer.
  1. (a) Series: $R_{eq} = 240 + 144 = 384\ \Omega$, so $I = \frac{120}{384} = 0.3125$ A, about 0.31 A.
  2. (b) $P_{60} = I^2R = (0.3125)^2(240) = 23$ W. $P_{100} = (0.3125)^2(144) = 14$ W.
    Why?
    Use $I^2R$ because the current is what the series bulbs share. Using $(\Delta V)^2/R$ with 120 V would be wrong: neither bulb has the full 120 V now.
  3. (c) Total: 23 + 14 = 37.5 W, which matches $I\varepsilon = (0.3125)(120) = 37.5$ W. In parallel each bulb gets its full 120 V, so the total is 160 W.
    Why?
    Checking that the battery's power equals the sum of the resistors' power catches almost every arithmetic slip.

Answer: (a) 0.31 A (b) 23 W for the "60 W" bulb and 14 W for the "100 W" bulb (c) 37.5 W in series, versus 160 W in parallel.

Stuck? Get a hint
  1. First find each bulb's resistance from its rating: R = ΔV²/P.
  2. In series the resistances add, then I = ε/$R_{eq}$.
  3. Same current in both, so compare I²R.

A household example to make the units concrete. A 1200 W kettle on a 120 V line draws $I = \frac{P}{\Delta V} = 10$ A and has resistance $R = \frac{\Delta V}{I} = 12\ \Omega$. In 3.0 minutes it delivers $Pt = (1200)(180) = 2.16 \times 10^5$ J to the water. If the power changes with time, you'd integrate: $E = \int P\,dt$.

Check yourself
The voltage across a fixed resistor is doubled. What happens to the power it dissipates?
  1. AIt doubles.
  2. BIt quadruples.
  3. CIt halves.
  4. DIt stays the same, because R is fixed.
Show the answer

B. $P = \frac{(\Delta V)^2}{R}$ with R fixed, so doubling ΔV multiplies P by 4. (The current doubles too: $P = I\Delta V$ goes up by 2 × 2.) The trap is "doubles", which forgets that the current also changes.

  • $P = I\Delta V$ for any element. For a resistor, also $I^2R$ and $\frac{(\Delta V)^2}{R}$.
  • Series: bigger R, more power. Parallel: smaller R, more power. Brightness follows power.
  • Power delivered by the sources = power used by the resistors. Use it as a check.
  • Energy is $\int P\,dt$. A power rating is the power at the rated voltage only.