AP Physics C: E&M · Unit 11 lecture · Part 3 of 11 · 9 min

11.3 Resistance, resistivity and Ohm's lawWhat sets a resistance

Mr. Thompkins
Same battery, two wires: one gets hot enough to toast bread, the other barely warms. The difference is resistance, and it depends on two things: what the wire is made of and what shape it is. Let's see why both matter.

Resistance is defined as the ratio of the potential difference across an object to the current through it: $R = \frac{\Delta V}{I}$, in ohms (1 Ω = 1 V/A). A big resistance means it takes a lot of voltage to push a little current.

For a wire of uniform material and cross-section, $R = \frac{\rho L}{A}$. Length L in the numerator: a longer wire is like a longer crowded hallway, more collisions along the way. Area A in the denominator: a thicker wire is more lanes side by side. The resistivity ρ (rho, in Ω·m) belongs to the material. Copper is about $1.7 \times 10^{-8}\ \Omega\cdot\text{m}$; nichrome, used in toaster coils, is about $1.1 \times 10^{-6}$, sixty-five times more. For most metals, resistivity rises with temperature, because the hotter ions vibrate more and scatter the electrons more. Its inverse, $\sigma = 1/\rho$, is the conductivity.

length Larea AImaterial: $\rho$R = ρL / Alonger: more R. thicker: less R.
Resistance depends on material (ρ) and shape: proportional to length, inversely proportional to cross-sectional area.
?Wait, what's the electric field inside a wire? I thought E = 0 inside conductors.
That rule from Unit 10 is for conductors in electrostatic equilibrium, with no current. A wire carrying current is not in equilibrium. A field inside it pushes the charges along. For a uniform wire of length L with ΔV across it, $E = \frac{\Delta V}{L}$.

Ohm's law says that for many materials, called ohmic, R stays constant as you change the voltage, so $\Delta V = IR$ with a fixed R and the I-ΔV graph is a straight line through the origin. Inside the material the same law reads $\vec E = \rho\vec J$: the field drives the current density, and the resistivity sets how much field it takes. Not everything is ohmic. A lamp filament heats up as the current grows, its resistivity rises, and its graph bends over.

02468101200.40.81.21.6$\Delta V$ (V)I (A)$8.0\ \Omega$ resistorlamp$5.7\ \Omega$ hereequal R
An ohmic 8.0 Ω resistor gives a straight line. A lamp (I = 0.35√ΔV here) bends over as it heats. Its resistance at a point is ΔV/I there: 5.7 Ω at 4.0 V, 9.9 Ω at 12 V. The two match only where they cross, at 7.84 V.
Pause and think
On the lamp curve above, is the resistance at a point equal to the slope of the curve there?
I thought about it. Show me
No. Resistance is $\Delta V/I$ at that point, the ratio of the coordinates. Only for a straight line through the origin does the slope (I over ΔV) equal 1/R everywhere. For the lamp at 4.0 V: $R = 4.0/0.70 = 5.7\ \Omega$, while the slope of the curve there, $\frac{dI}{d(\Delta V)} = 0.088$ A/V, is only about half of $1/5.7 = 0.18$ A/V.
A heating wire
A heating element is a nichrome wire ($\rho = 1.1 \times 10^{-6}\ \Omega\cdot\text{m}$) 2.0 m long with a diameter of 0.40 mm, connected across 12 V. Find (a) its resistance, (b) the current, and (c) the electric field inside the wire. (d) Check (c) using $E = \rho J$.
  1. (a) $A = \pi(0.20 \times 10^{-3})^2 = 1.26 \times 10^{-7}\ \text{m}^2$. $R = \frac{\rho L}{A} = \frac{(1.1 \times 10^{-6})(2.0)}{1.26 \times 10^{-7}} = 17.5\ \Omega$.
    Why?
    Convert millimeters to meters before squaring. $(0.20\ \text{mm})^2$ is $4.0 \times 10^{-8}\ \text{m}^2$.
  2. (b) $I = \frac{\Delta V}{R} = \frac{12}{17.5} = 0.69$ A.
  3. (c) Uniform wire: $E = \frac{\Delta V}{L} = \frac{12\ \text{V}}{2.0\ \text{m}} = 6.0$ V/m, pointing along the current.
  4. (d) $J = \frac{I}{A} = \frac{0.686}{1.26 \times 10^{-7}} = 5.5 \times 10^6\ \text{A/m}^2$, and $\rho J = (1.1 \times 10^{-6})(5.45 \times 10^6) = 6.0$ V/m. It matches.
    Why?
    Two routes to the same number is the best check you have. $E = \rho J$ is just $\Delta V = IR$ divided through by the length.

Answer: (a) 17.5 Ω (b) 0.69 A (c) 6.0 V/m (d) $\rho J = 6.0$ V/m, the same.

Stuck? Get a hint
  1. Start with the area. Radius = half of 0.40 mm, in meters.
  2. $R = \rho L/A$, then $I = \Delta V/R$.
  3. Inside a uniform wire, the field is the voltage divided by the length.

When the wire is not uniform

Here's the calculus version, which the exam does ask. If the area or the resistivity changes along the wire, cut it into thin slices of length dx. The slices are in series, so their resistances add: $dR = \frac{\rho\,dx}{A(x)}$ and $R = \int \frac{\rho\,dx}{A(x)}$. For example, a rod of length L whose area grows steadily from $A_0$ to $2A_0$, so $A(x) = A_0\left(1 + \frac{x}{L}\right)$, has $R = \frac{\rho}{A_0}\int_0^L \frac{dx}{1 + x/L} = \frac{\rho L}{A_0}\ln 2 \approx 0.69\frac{\rho L}{A_0}$. That's between the resistance of a rod of area $A_0$ and one of area $2A_0$, as it should be.

?Wait, what's the integral of 1/(1 + x/L)?
Substitute $u = 1 + x/L$, so $dx = L\,du$. Then $\int \frac{dx}{1 + x/L} = L\ln(1 + x/L)$. From 0 to L that's $L(\ln 2 - \ln 1) = L\ln 2$.
Check yourself
A wire is replaced by one made of the same material that is three times as long and has twice the diameter. By what factor does the resistance change?
  1. A3/4
  2. B3/2
  3. C6
  4. D3
Show the answer

A. $R \propto L/A$ and $A \propto d^2$. Length ×3, area ×4: $R$ changes by $3/4$. The trap is 3/2, which doubles the area instead of quadrupling it when the diameter doubles.

Exam tip from Mr. T

"Determine the resistance" with a graph of ΔV against I (or I against ΔV) means: if it's a straight line through the origin, use the slope (ΔV/I, or its reciprocal). If it's curved, read one point and divide. Say which one you did.

  • $R = \frac{\Delta V}{I}$. For a uniform wire, $R = \frac{\rho L}{A}$; ρ is a property of the material.
  • Ohmic: R constant, straight I-ΔV line through the origin. In the material, $\vec E = \rho\vec J$.
  • Non-uniform wire: series slices, $R = \int \frac{\rho\,dx}{A}$.
  • Resistivity of metals rises with temperature, which is why a lamp's graph bends.