AP Physics C: Mechanics · Unit 6 lecture · Part 3 of 11 · 8 min

6.2 Torque and workWork done while turning

Mr. Thompkins
Push a door at its edge and it swings open. Push the same edge straight toward the hinges and nothing happens, however hard you push. Work done by a torque follows exactly that rule.

In Unit 3, work was $dW = \vec F\cdot d\vec s$: only the part of the force along the motion does work. When an object turns through a small angle $d\theta$, a point at distance $r$ from the axis moves a distance $ds = r\,d\theta$, along the tangent. So only the tangential part of the force, $F_\perp$, does work: $dW = F_\perp\,r\,d\theta$. And $rF_\perp$ is the torque. So $dW = \tau\,d\theta$, and over a whole turn of the object, $W = \int_{\theta_1}^{\theta_2} \tau\,d\theta$.

?Wait, what is torque again?
Torque is $\vec\tau = \vec r \times \vec F$, with magnitude $\tau = rF\sin\phi$, where $\phi$ is the angle between $\vec r$ and $\vec F$. You can read it as $rF_\perp$ (distance times the perpendicular part of the force) or as $r_\perp F$ (lever arm times force). Counterclockwise is usually positive.
rFradial parttangential partradial: no worktangential: dW = F⊥ r dθso dW = τ dθ
A force on a wheel's rim. The radial part pulls straight along the radius and does no work. The tangential part is the only part that turns the wheel, so it is the only part that does work.

If the torque is constant, the integral is just $W = \tau\,\Delta\theta$. If the torque changes with angle, you integrate, and on a graph of $\tau$ against $\theta$, the work is the area under the curve. Measure $\theta$ in radians, so that N·m times rad gives joules.

The rotational work-energy theorem says the net work done by all torques equals the change in rotational kinetic energy: $W_{net} = \Delta K_{rot} = \tfrac12 I\omega_f^2 - \tfrac12 I\omega_i^2$. You can prove it with the same chain-rule trick as Unit 3: $\Sigma\tau = I\alpha = I\frac{d\omega}{dt} = I\frac{d\omega}{d\theta}\frac{d\theta}{dt} = I\omega\frac{d\omega}{d\theta}$. Multiply by $d\theta$ and integrate: $\int\Sigma\tau\,d\theta = \int I\omega\,d\omega = \Delta\left(\tfrac12 I\omega^2\right)$.

?Wait, how did the chain-rule trick work in Unit 3?
Write acceleration as $a = \frac{dv}{dt} = \frac{dv}{dx}\frac{dx}{dt} = v\frac{dv}{dx}$. Then $F\,dx = mv\,dv$, and integrating gives $W = \Delta\left(\tfrac12 mv^2\right)$. The rotational version just swaps $x \to \theta$, $v \to \omega$, $m \to I$.

Power is how fast work is done: $P = \frac{dW}{dt} = \tau\frac{d\theta}{dt} = \tau\omega$. It is the rotational partner of $P = Fv$. A car engine's power rating is torque times angular speed of the crankshaft.

012345-20246810θ (rad)τ (N·m)motor: W = 20 Jτ = 2.0 + 1.5θfriction: W = −4.0 J
Torque against angle for a wheel spun up by a motor while friction drags on the axle. Blue area: work done by the motor. Red area below the axis: negative work done by friction.
Pause and think
In the graph, the friction torque lies below the axis. What does the area between it and the axis mean, and what is it?
I thought about it. Show me
It is the work done by friction, and it is negative, because friction's torque opposes the rotation: $(-1.0\ \text{N}\cdot\text{m})(4.0\ \text{rad}) = -4.0\ \text{J}$. Friction takes 4.0 J of energy out of the wheel's motion and turns it into thermal energy in the axle.
Spin-up with a changing torque
A wheel with $I = 0.30\ \text{kg}\cdot\text{m}^2$ starts from rest. A motor applies a torque $\tau_m = 2.0 + 1.5\theta$ (N·m, with θ in rad), while friction in the axle applies a constant 1.0 N·m opposing the motion. (a) How much work does the motor do in the first 4.0 rad? (b) What is the wheel's angular speed at 4.0 rad? (c) At what rate is the motor doing work at that moment?
  1. (a) $W_m = \int_0^{4.0}(2.0 + 1.5\theta)\,d\theta = \left[2.0\theta + 0.75\theta^2\right]_0^{4.0} = 8.0 + 12 = 20\ \text{J}$.
    Why?
    This is the area of the blue trapezoid in the graph: average height 5.0 N·m times width 4.0 rad.
  2. Friction's work: $W_f = (-1.0)(4.0) = -4.0\ \text{J}$, so $W_{net} = 20 - 4.0 = 16\ \text{J}$.
  3. (b) Work-energy theorem: $W_{net} = \tfrac12 I\omega^2 - 0$, so $\omega = \sqrt{\frac{2(16)}{0.30}} = 10.3\ \text{rad/s}$.
    Why?
    Use the net work, not just the motor's work. The work-energy theorem is about the total.
  4. (c) At 4.0 rad the motor's torque is $2.0 + 1.5(4.0) = 8.0\ \text{N}\cdot\text{m}$, so $P = \tau\omega = (8.0)(10.3) = 83\ \text{W}$.
    Why?
    Power is an instant-by-instant quantity, so use the torque and $\omega$ at that moment, not averages.

Answer: (a) 20 J. (b) About 10 rad/s. (c) About 83 W.

Stuck? Get a hint
  1. Work is $\int\tau\,d\theta$. Integrate the motor's torque from 0 to 4.0 rad.
  2. Friction does negative work: torque times angle, with a minus sign.
  3. Then set net work equal to $\tfrac12 I\omega^2$ and use $P = \tau\omega$.
Check yourself
An electric motor delivers a steady torque of 40 N·m while its shaft turns at 1500 revolutions per minute. What power does it deliver?
  1. A60 kW
  2. B6.3 kW
  3. C1.0 kW
  4. D0.63 kW
Show the answer

B. Convert first: $1500\ \text{rev/min} = 25\ \text{rev/s} = 157\ \text{rad/s}$. Then $P = \tau\omega = (40)(157) = 6.3 \times 10^3\ \text{W}$. The trap at 60 kW multiplied by rev/min; the one at 1.0 kW used rev/s, which forgets the factor of 2π.

  • $dW = \tau\,d\theta$, so $W = \int\tau\,d\theta$: the area under a $\tau(\theta)$ graph, with θ in radians.
  • Only the tangential part of a force does work on a rotating object. A radial force does none.
  • Rotational work-energy theorem: $W_{net} = \Delta\left(\tfrac12 I\omega^2\right)$.
  • Power: $P = \tau\omega$.