11.8 RC circuits: discharging, networks and dataDischarging, bigger circuits, and measuring τ

Disconnect the battery and let a charged capacitor push current through a resistor. Walking around the loop: $\frac{q}{C} - IR = 0$. Now the capacitor's charge is draining, so the current is $I = -\frac{dq}{dt}$. That gives $\frac{dq}{dt} = -\frac{q}{RC}$, whose solution is $q = q_0e^{-t/RC}$. Voltage and current follow the same curve: $V_C = V_0e^{-t/RC}$ and $I = \frac{V_0}{R}e^{-t/RC}$.
?Wait, why does dq/dt = −q/RC give an exponential?
- (a) $\tau = RC = (10 \times 10^3)(470 \times 10^{-6}) = 4.7$ s. $I_0 = \frac{V_0}{R} = \frac{12}{10 \times 10^3} = 1.2$ mA.
- (b) $\frac{1}{2} = e^{-t/RC}$, so $t = RC\ln 2 = (4.7)(0.693) = 3.3$ s.
- (c) Energy goes as $q^2$: $U = U_0e^{-2t/RC}$. Setting that to half: $t = \frac{RC\ln 2}{2} = 1.6$ s.
Why?
The energy halves sooner than the charge, because when the charge is at 71% the energy (charge squared) is already at 50%. - (d) All the stored energy ends up as heat: $U_0 = \frac{1}{2}CV_0^2 = \frac{1}{2}(470 \times 10^{-6})(12)^2 = 0.034$ J.
Why?
You could also integrate $\int_0^\infty I^2R\,dt = \frac{V_0^2}{R}\cdot\frac{RC}{2} = \frac{1}{2}CV_0^2$. Same answer.
Answer: (a) 4.7 s and 1.2 mA (b) 3.3 s (c) 1.6 s (d) 0.034 J.
Stuck? Get a hint
- τ is R times C, in ohms and farads.
- For half the charge, solve $e^{-t/RC} = 0.5$ with a natural log.
- Energy is proportional to q², so it decays as $e^{-2t/RC}$.
Capacitors inside bigger circuits
Often the capacitor sits in one branch of a network. Use the two limits. Just after a switch closes, replace each empty capacitor with a wire and solve the resistor circuit. Long after, remove each capacitor (a break) and solve again; the capacitor's voltage then equals the voltage across whatever it's in parallel with. The time constant uses the resistance the capacitor "sees": look out from its two terminals with each ideal battery replaced by a wire.
- (a) Just after: the empty capacitor acts like a wire, which shorts $R_2$. Only $R_1$ limits the current: $I = \frac{18}{3.0 \times 10^3} = 6.0$ mA, and all of it flows into the capacitor.
Why?
The short is the key insight: a wire in parallel with $R_2$ means $R_2$ has no voltage and no current at that instant. - (b) Long after: the capacitor is a break. $R_1$ and $R_2$ are in series: $I = \frac{18}{9.0 \times 10^3} = 2.0$ mA.
- (c) $V_C = V_{R_2} = (2.0\ \text{mA})(6.0\ \text{k}\Omega) = 12$ V, so $Q = CV = (20\ \mu\text{F})(12\ \text{V}) = 240\ \mu$C.
- (d) Looking out from C with the battery as a wire, $R_1$ and $R_2$ are in parallel: $\frac{(3.0)(6.0)}{9.0} = 2.0$ kΩ. So $\tau = (2.0 \times 10^3)(20 \times 10^{-6}) = 0.040$ s.
Why?
Not $R_1C$ and not $(R_1 + R_2)C$. The capacitor charges through both resistors at once.
Answer: (a) 6.0 mA (b) 2.0 mA (c) 240 μC at 12 V (d) 40 ms.
Stuck? Get a hint
- Just after: replace the capacitor with a wire. What happens to R₂?
- Long after: remove the capacitor. Now R₁ and R₂ are simply in series.
- The capacitor's final voltage equals R₂'s voltage, because they're in parallel.
I thought about it. Show me
| Element | Just after a switch | Long after | Never jumps |
|---|---|---|---|
| Resistor | $\Delta V = IR$ at every instant | $\Delta V = IR$ | Nothing: it reacts at once |
| Empty capacitor | Acts like a wire (V = 0) | Acts like a break (I = 0) | Its charge and voltage $q/C$ |
| Charged capacitor | Keeps its voltage | Discharged, if it has a path | Its charge and voltage $q/C$ |
Capacitors also combine, the opposite way from resistors. In parallel they share ΔV and their charges add, so $C_p = C_1 + C_2 + \dots$. In series they carry the same charge (the inner plates form an isolated conductor) and their voltages add, so $\frac{1}{C_s} = \frac{1}{C_1} + \frac{1}{C_2} + \dots$. For example, 6.0 μF and 3.0 μF in series make 2.0 μF. Across 12 V each holds 24 μC, so the 6.0 μF has 4.0 V and the 3.0 μF has 8.0 V: the smaller capacitor takes the bigger share of the voltage.
Measuring a time constant
On an Experimental Design and Analysis question, you'll be handed decay data and asked for R or C. The move is to linearize. Take the natural log of $V_C = V_0e^{-t/RC}$: $\ln V_C = \ln V_0 - \frac{1}{RC}t$. That's a straight line in t with slope $-\frac{1}{RC}$ and intercept $\ln V_0$. A student discharges a capacitor through 100 kΩ and reads 10.0, 4.8, 2.3, 1.1, 0.53 and 0.25 V at t = 0, 5, 10, 15, 20 and 25 s.
?Wait, why does taking ln straighten an exponential?
- Take logs: $\ln V$ = 2.303, 1.569, 0.833, 0.095, −0.635, −1.386.
Why?
Plot $\ln V_C$ on the vertical axis and t on the horizontal axis, with labeled axes and units. That's a rubric point. - Draw a best-fit line and read its slope from two points on the line (not data points): from (0, 2.31) to (25 s, −1.38), slope $= \frac{-1.38 - 2.31}{25} = -0.147\ \text{s}^{-1}$.
- Slope $= -\frac{1}{RC}$, so $RC = \frac{1}{0.147} = 6.8$ s and $C = \frac{6.8}{100 \times 10^3} = 6.8 \times 10^{-5}$ F.
Answer: $C \approx 68\ \mu\text{F}$. The intercept, $e^{2.31} \approx 10$ V, matches the starting voltage.
- A100 μF
- B10 μF
- C160 μF
- D0.25 μF
Show the answer
A. $\frac{1}{RC} = 0.25\ \text{s}^{-1}$, so $RC = 4.0$ s and $C = \frac{4.0}{40 \times 10^3} = 1.0 \times 10^{-4}$ F = 100 μF. The trap is 10 μF, a slip of a factor of 10 in the kilo-ohm conversion.

When a graph of $V_C$ or I against t is given, find τ from it first: the time to fall to 37%, the time to rise to 63%, or the half-time divided by 0.69. Mark the point you read on the graph. Then use τ = RC.
- Discharging: $q = q_0e^{-t/RC}$, with $I = -\frac{dq}{dt}$. Charge halves every $0.69RC$; energy halves every $0.35RC$.
- Networks: just after, empty capacitors are wires; long after, they are breaks with the voltage of their parallel partner.
- τ uses the resistance the capacitor sees, with batteries replaced by wires. Discharge paths can differ.
- Capacitors: parallel add, $\frac{1}{C_s}$ adds in series. Linearize decay data with $\ln V$ against t: slope $-1/RC$.