AP Physics C: E&M · Unit 11 lecture · Part 6 of 11 · 8 min

11.5 Internal resistance and metersReal batteries, real meters

Mr. Thompkins
Ever notice your car's headlights dim for a moment when the engine cranks? The battery hasn't lost its emf. It has a little resistance inside it, and a big current makes that inside resistance cost you volts. Let's model it.

A real battery behaves like an ideal emf ε in series with a small internal resistance r, both inside the same case. When a current I flows out of it, the internal resistance takes a drop Ir, so the voltage you actually get at the terminals is $\Delta V_{terminal} = \varepsilon - Ir$. With no current, the terminal voltage equals ε. With a big current, it sags.

εrreal batteryAload RVammeter: in the loopvoltmeter: acrossthe terminals
Inside the dashed box: an ideal emf ε in series with internal resistance r. The ammeter sits in the loop; the voltmeter connects across the two terminals and reads ε − Ir.

Connect a load R, and r and R are simply in series: $I = \frac{\varepsilon}{R + r}$. Short the terminals with a wire (R = 0) and you get the largest possible current, $\frac{\varepsilon}{r}$, with the terminal voltage at zero and all the power heating the battery. That's why shorting a battery is dangerous.

?Wait, why is the terminal voltage the same as the voltage across the load?
An ideal wire has no resistance, so both ends of a wire are at the same potential. The battery's + terminal is wired straight to the top of R and its − terminal to the bottom, so the two pairs of points have the same potential difference.

Meters

An ammeter measures the current through itself, so it goes in series, inside the loop. An ideal ammeter has zero resistance, so it doesn't change the current it measures. A voltmeter measures the potential difference between its two leads, so it goes in parallel, across the element. An ideal voltmeter has infinite resistance, so it draws no current. Wire them backward and they wreck the circuit: an ideal ammeter in parallel shorts out the element, and an ideal voltmeter in series stops the current and reads (almost) the full emf.

?Wait, how do I read slope and intercept off a line?
A line $y = mx + b$ has slope m (rise over run) and vertical intercept b (the value of y when x = 0). Match $\Delta V = \varepsilon - rI$ to it: y is ΔV, x is I, the intercept is ε and the slope is $-r$.
024681012012345678current I (A)terminal voltage (V)slope $= -r$(1.2 A, 5.4 V)(2.4 A, 4.8 V)ε = 6.0 Vshort: $\varepsilon/r$
Terminal voltage falls in a straight line as current grows: ΔV = ε − Ir. The intercept is ε, the slope is −r, and it reaches zero at the short-circuit current ε/r.
Pause and think
A voltmeter is connected alone across a battery's terminals, with nothing else attached. Does it read ε, ε − Ir, or zero?
I thought about it. Show me
It reads ε. An ideal voltmeter draws no current, so I = 0 and $\varepsilon - Ir = \varepsilon$. That's the one situation where a voltmeter shows the emf of a real battery.
Find ε and r from two readings
A student connects a battery to different loads. With one load the ammeter reads 1.2 A and the voltmeter across the terminals reads 5.4 V. With a second load it reads 2.4 A and 4.8 V. (a) Find the internal resistance and the emf. (b) Find the two load resistances. (c) What current would flow if the terminals were shorted?
  1. (a) Write $\Delta V = \varepsilon - Ir$ twice: $5.4 = \varepsilon - 1.2r$ and $4.8 = \varepsilon - 2.4r$.
    Why?
    Two unknowns need two equations. Each reading gives one.
  2. Subtract: $0.6 = 1.2r$, so $r = 0.50\ \Omega$. Then $\varepsilon = 5.4 + (1.2)(0.50) = 6.0$ V.
    Why?
    On the graph, r is minus the slope between the two points: $-\frac{4.8 - 5.4}{2.4 - 1.2} = 0.50\ \Omega$, and ε is the intercept.
  3. (b) The voltmeter reading is also the load's voltage: $R = \frac{5.4}{1.2} = 4.5\ \Omega$ and $\frac{4.8}{2.4} = 2.0\ \Omega$.
  4. (c) $I_{short} = \frac{\varepsilon}{r} = \frac{6.0}{0.50} = 12$ A.

Answer: (a) $r = 0.50\ \Omega$, $\varepsilon = 6.0$ V (b) 4.5 Ω and 2.0 Ω (c) 12 A.

Stuck? Get a hint
  1. Write ΔV_terminal = ε − Ir for each reading.
  2. Subtract one equation from the other. ε cancels.
  3. r = 0.6 V / 1.2 A. Then put r back into either equation for ε.
Check yourself
A battery with emf 12 V and internal resistance 1.0 Ω drives a 5.0 Ω resistor. What is the terminal voltage?
  1. A12 V
  2. B10 V
  3. C2.0 V
  4. D11 V
Show the answer

B. $I = \frac{12}{5.0 + 1.0} = 2.0$ A, so $\Delta V = 12 - (2.0)(1.0) = 10$ V, which is also $IR = (2.0)(5.0)$. The trap is 12 V: that's the reading only when no current flows.

Check yourself
An ideal ammeter is mistakenly connected in parallel with a resistor in a working circuit. What happens?
  1. AIt reads the resistor's current and nothing else changes.
  2. BIt shorts out the resistor, so the resistor's current drops to zero and the circuit current rises.
  3. CIt reads zero because ammeters only work in series.
  4. DIt stops all the current in the circuit.
Show the answer

B. An ideal ammeter has zero resistance. In parallel it is a wire across the resistor: the resistor gets no voltage and no current, the total resistance falls, and the circuit current goes up. Stopping the current (the last choice) is what a voltmeter in series does.

  • Real battery: emf ε in series with internal r. $\Delta V_{terminal} = \varepsilon - Ir$; $I = \frac{\varepsilon}{R + r}$.
  • Terminal voltage equals ε only when no current flows. A short draws $\varepsilon/r$.
  • Ammeter: in series, ideal R = 0. Voltmeter: in parallel, ideal R = infinite.
  • Two (I, ΔV) readings, or a ΔV-against-I graph, give ε (intercept) and r (minus the slope).