AP Physics C: E&M · Unit 11 lecture · Part 1 of 11 · 8 min

11.1 Electric current and current densityCurrent: charge on the move

By the end: Use current, resistance and power to analyze any DC circuit with series and parallel parts, real batteries and meters, solve multi-loop circuits with Kirchhoff's rules, and derive and read the exponential behavior of RC circuits.
Mr. Thompkins
Hi, I'm Mr. T. Here's a puzzle to start the unit. Flip a light switch and the bulb across the room lights instantly. Yet the electrons in that wire crawl along slower than a snail. By the end of this section you'll know exactly how slow, and why the lamp doesn't care.

Up to now, charges sat still: Units 8 to 10 were electrostatics. Now we let them move. Electric current is the rate at which charge passes through a cross section of a wire. If a small amount of charge $dq$ crosses in a small time $dt$, the current is $I = \frac{dq}{dt}$. The unit is the ampere: 1 A = 1 C/s, one coulomb every second.

?Wait, what's a coulomb again?
The coulomb is the unit of charge. One electron carries $-e = -1.6 \times 10^{-19}$ C, so one coulomb is the charge of about $6.25 \times 10^{18}$ electrons. Charge is conserved: it can move around, but the total never changes.

By convention, the direction of current is the way positive charge would move. In a metal wire the charges that actually move are electrons, which are negative, so they drift opposite to the current arrow. That sounds confusing, but it never changes an answer: negative charge moving left carries charge exactly the way positive charge moving right does. You'll draw current arrows the conventional way for the rest of the course.

Because $I = \frac{dq}{dt}$, the charge that passes in a time interval is the integral of the current: $q = \int I\,dt$. On a graph of I against t, that's the area under the curve, the same way the area under a velocity graph is displacement.

01234502468t (s)I (A)area = charge = 12 C6.0 A
A current that falls steadily from 6.0 A to zero in 4.0 s. The shaded area is the charge that passed: ½(4.0 s)(6.0 A) = 12 C.
?Wait, how do I integrate a straight line again?
For $I = a + bt$, $\int_0^T (a + bt)\,dt = aT + \frac{b}{2}T^2$. You can also just find the area of the shape: a triangle has area ½ × base × height, a rectangle base × height.

Zooming into the wire

Current density $\vec J$ is current per unit area, pointing along the flow. If it's spread evenly over a wire of cross-section A, then $J = I/A$. If it isn't, the current through a surface is $I = \int \vec J \cdot d\vec A$: add up J times each little piece of area.

Here's where the drift speed comes from. Picture the wire full of free electrons, n of them per cubic meter, each with charge q, all drifting at average speed $v_d$. In a time dt, every carrier within a distance $v_d\,dt$ of a cross section crosses it. That slice has volume $A v_d\,dt$, so the charge through is $dq = nqAv_d\,dt$. Divide by dt: $I = nqAv_d$, or $J = nqv_d$.

$v_d\,dt$area Acurrent Ifield $\vec E$electrons drift left (blue arrows)
Every carrier within one drift distance of the area A crosses it in the time dt. Counting them gives J = nq times the drift speed. Electrons drift opposite the field and the current.
Pause and think
Copper has about $8.5 \times 10^{28}$ free electrons per cubic meter. Predict: is the drift speed in a lamp cord closer to a meter per second, a centimeter per second, or a fraction of a millimeter per second?
I thought about it. Show me
A fraction of a millimeter per second. There are so many carriers that each one only has to move a tiny bit to carry an ampere. The walk below puts a number on it.
Find the drift speed
A copper wire 1.0 mm in diameter carries a steady 2.5 A. Copper has $n = 8.5 \times 10^{28}$ free electrons per cubic meter. (a) Find the current density. (b) Find the drift speed. (c) How long would one electron take to drift 1.0 m?
  1. (a) Area: $A = \pi r^2 = \pi(0.50 \times 10^{-3}\ \text{m})^2 = 7.85 \times 10^{-7}\ \text{m}^2$. So $J = \frac{I}{A} = \frac{2.5}{7.85 \times 10^{-7}} = 3.2 \times 10^{6}\ \text{A/m}^2$.
    Why?
    Use the radius, in meters. Using the diameter makes the area four times too big, the most common slip here.
  2. (b) Solve $J = nev_d$ for $v_d$: $v_d = \frac{J}{ne} = \frac{3.18 \times 10^6}{(8.5 \times 10^{28})(1.6 \times 10^{-19})} = 2.3 \times 10^{-4}$ m/s.
    Why?
    That's 0.23 mm per second. Writing the formula in symbols first, then substituting with units, is how graders want to see it.
  3. (c) $t = \frac{1.0\ \text{m}}{2.3 \times 10^{-4}\ \text{m/s}} = 4.3 \times 10^3$ s, about 71 minutes.
    Why?
    The lamp lights at once anyway, because the electric field that pushes the electrons sets up along the whole wire almost at the speed of light. Every electron in the wire starts drifting at nearly the same moment, like water in a full hose.

Answer: (a) $3.2 \times 10^6\ \text{A/m}^2$ (b) $2.3 \times 10^{-4}$ m/s (c) about $4.3 \times 10^3$ s, over an hour per meter.

Stuck? Get a hint
  1. Start with the area of the cross section. What's the radius in meters?
  2. $J = I/A$, then $J = nqv_d$ with $q = e$.
  3. $v_d = \frac{I}{neA}$. Put in 2.5 A, $8.5 \times 10^{28}$, $1.6 \times 10^{-19}$ C and $7.85 \times 10^{-7}\ \text{m}^2$.

One more calculus move the exam likes. Suppose the current density isn't uniform, say $J = J_0\frac{r}{R}$ in a wire of radius R, larger near the surface. Slice the cross section into thin rings of radius r and width dr. Each ring has area $2\pi r\,dr$, so $I = \int_0^R J_0\frac{r}{R}\,2\pi r\,dr = \frac{2\pi J_0}{R}\cdot\frac{R^3}{3} = \frac{2}{3}\pi J_0R^2$. Hold on to that ring trick: you'll use it again with Ampère's law in Unit 12.

Check yourself
The charge that has passed a point in a wire is $q(t) = 3.0t^2 + 2.0t$, in millicoulombs with t in seconds. What is the current at t = 2.0 s?
  1. A14 mA
  2. B16 mA
  3. C12 mA
  4. D8.0 mA
Show the answer

A. $I = \frac{dq}{dt} = 6.0t + 2.0$ mA, which is 14 mA at t = 2.0 s. The top trap is 16 mA: that's $q(2.0)$, the charge itself, not its rate of change.

  • $I = \frac{dq}{dt}$ and $q = \int I\,dt$: charge is the area under an I-t graph.
  • Current points the way positive charge moves. Electrons in a metal drift the other way.
  • $J = I/A$ when uniform, $I = \int \vec J \cdot d\vec A$ in general, and $J = nqv_d$.
  • Drift speeds are tiny (about $10^{-4}$ m/s) because n is huge. The signal still travels almost at light speed.