AP Physics C: E&M · Unit 10 lecture · Part 5 of 10 · 10 min

10.3 CapacitorsCapacitance: charge per volt

Mr. Thompkins
Every phone, laptop and camera flash has capacitors in it. A capacitor is just two conductors with a gap, holding equal and opposite charge. It stores charge, and more importantly, it stores energy that it can dump in a hurry.

Put charge $+Q$ on one conductor and $-Q$ on the other. Between them there's a field, and so a potential difference ΔV. Double Q and every field doubles, so ΔV doubles too. The ratio is a constant that depends only on the shape, size and spacing of the conductors (and the material between them). That ratio is the capacitance:

$$C = \frac{Q}{\Delta V}$$

Its unit is the farad: $1\ \text{F} = 1\ \text{C/V}$. A farad is enormous; real capacitors are measured in microfarads (μF), nanofarads (nF) and picofarads (pF, $10^{-12}$ F). By convention, Q means the size of the charge on either plate. The net charge on a capacitor is zero.

?Wait, what's the field between two large oppositely charged plates?
From Unit 8: each sheet makes $\sigma/(2\varepsilon_0)$. Between the plates their fields point the same way and add to $\sigma/\varepsilon_0$; outside they cancel. So the field is uniform between the plates and nearly zero outside.
?Wait, why is a farad so huge?
Try it: a 1 F parallel-plate capacitor with a 1.0 mm air gap needs $A = \frac{Cd}{\varepsilon_0} = \frac{(1)(1.0 \times 10^{-3})}{8.85 \times 10^{-12}} = 1.1 \times 10^8\ \text{m}^2$, a square about 11 km on a side. That's why everyday capacitors are rated in μF, nF and pF, and why the "supercapacitors" that do reach farads use special materials with enormous internal surface area.

It helps to picture what Q and ΔV mean physically here. The battery acts like a pump: it pulls electrons off one plate and pushes them onto the other, until the plates' potential difference matches the battery's voltage. Then the flow stops. A bigger capacitance means the battery has to move more charge before that happens.

Deriving C for parallel plates

Plates of area A, separation d, charges $\pm Q$, with d much smaller than the plates' size. Follow the standard derivation, which is worth points on a free-response question:

  1. Field (Gauss's law, pillbox at the inner face of a plate): $E = \frac{\sigma}{\varepsilon_0} = \frac{Q}{\varepsilon_0 A}$.
  2. Potential difference (uniform field): $\Delta V = Ed = \frac{Qd}{\varepsilon_0 A}$.
  3. Capacitance: $C = \frac{Q}{\Delta V} = \frac{\varepsilon_0 A}{d}$.
+Q−Q$d$plate area Auniform$E = \sigma/\varepsilon_0$outside: E ≈ 0
A parallel-plate capacitor. Between the plates the field is uniform; outside it is nearly zero. Near the edges it bulges out (fringing), which we ignore when the gap is small.

Notice Q canceled. C depends only on geometry: bigger plates hold more charge per volt, a wider gap holds less. Once a capacitor is built, its C is fixed, and $Q = C\Delta V$ tells you how much charge a given voltage pushes onto it.

02468101200.511.522.5$\Delta V$ (V)$Q$ (nC)slope = C = 177 pF2.12 nC at 12 V
Charge against voltage for one capacitor: a straight line through the origin whose slope is C.
Pause and think
A student says, "If I double the voltage across a capacitor, its capacitance doubles, since C depends on V." What's wrong?
I thought about it. Show me
Doubling ΔV doubles Q too, so the ratio $Q/\Delta V$ stays the same. C is set by the geometry ($\varepsilon_0 A/d$), not by the charge or voltage you happen to use.
A parallel-plate capacitor
Two plates, each 0.020 m² in area, are 1.0 mm apart in air and connected to a 12 V battery. Find (a) the capacitance, (b) the charge on each plate, and (c) the field between the plates.
  1. (a) $C = \frac{\varepsilon_0A}{d} = \frac{(8.85 \times 10^{-12})(0.020)}{1.0 \times 10^{-3}} = 1.77 \times 10^{-10}$ F $= 177$ pF.
    Why?
    Convert d to meters. Millimeters are the usual slip.
  2. (b) $Q = C\Delta V = (1.77 \times 10^{-10})(12) = 2.1 \times 10^{-9}$ C: $+2.1$ nC on one plate and $-2.1$ nC on the other.
  3. (c) $E = \frac{\Delta V}{d} = \frac{12}{1.0 \times 10^{-3}} = 1.2 \times 10^4$ V/m, from the positive plate to the negative.
    Why?
    Check with σ/ε₀: (2.12 × 10⁻⁹ / 0.020) / 8.85 × 10⁻¹² = 1.2 × 10⁴ V/m. Same.

Answer: (a) 177 pF. (b) $\pm 2.1$ nC. (c) $1.2 \times 10^4$ V/m.

Stuck? Get a hint
  1. C = ε₀A/d with d in meters.
  2. Q = CΔV.
  3. In a uniform field, E = ΔV/d.
Check yourself
The plate area of a parallel-plate capacitor is doubled and the gap is also doubled. What happens to C?
  1. AIt doubles.
  2. BIt halves.
  3. CIt stays the same.
  4. DIt quadruples.
Show the answer

C. $C = \varepsilon_0A/d$: doubling A doubles C and doubling d halves it. Net: no change.

  • $C = Q/\Delta V$: farads (C/V). Q is the charge on either plate.
  • Parallel plates: $E = Q/(\varepsilon_0A)$, $\Delta V = Ed$, $C = \varepsilon_0A/d$.
  • C depends only on geometry and material, never on Q or ΔV.
  • The derivation: Gauss for E, integrate for ΔV, divide for C.