AP Physics 1 · Unit 8 lecture · Part 7 of 11 · 7 min

8.4 Fluids and conservation laws: continuityWhat flows in must flow out

Mr. Thompkins
Put your thumb over the end of a garden hose and the water shoots out faster. You didn't add any water. So where did the speed come from? From the simplest conservation law in the unit.

Now the fluid moves. Think of water flowing steadily through a pipe that changes width. Water is (ideally) incompressible and it can't pile up anywhere or vanish, so every second, the same volume of water that enters one end must pass every cross section and leave the other end. That amount is the volume flow rate: the volume passing a point per second.

?Wait, what's a conservation law?
A rule that some total stays the same as a system changes: energy (Unit 3), momentum (Unit 4), and mass. Continuity is conservation of mass for a fluid that can't be squeezed, and Bernoulli (next section) is conservation of energy.

Picture a slice of water moving at speed $v$ through a pipe of cross-sectional area $A$. In one second it moves a distance $v$, sweeping out a volume $Av$. So the volume flow rate is $Av$, in m³/s. Continuity says it's the same everywhere along the pipe: $A_1v_1 = A_2v_2$. Since the density is constant, this is the same as saying mass is conserved: the mass flow rate $\rho Av$ is the same everywhere too.

$v_1$$v_2$big area $A_1$, slowsmall area $A_2$, fastsame volume per second: $A_1v_1 = A_2v_2$
Where the pipe is wide, the water moves slowly. Where it narrows, it must move faster, so the same volume passes each second.
?Wait, how does area change with diameter?
$A = \pi r^2 = \frac{\pi d^2}{4}$, so area goes with the square of the diameter. Half the diameter means one quarter of the area. A pipe 4 times as wide has 16 times the area.

So narrow means fast and wide means slow, in inverse proportion to the area. Rivers do this too: the water races through a narrow gorge and slows down where the river widens into a pool. Your thumb on the hose shrinks the opening area, so the water must leave faster.

Pause and think
A pipe of area $A$ carries water at speed $v$, then splits into three branches, each of area $\frac{A}{2}$. How fast does the water move in each branch?
I thought about it. Show me
$\frac{2}{3}v$. The total area of the branches is $3 \times \frac{A}{2} = 1.5A$, and the total flow rate $Av$ must pass through them: $Av = (1.5A)v_{branch}$, so $v_{branch} = \frac{v}{1.5}$. More total area, slower flow, even though each branch is narrower.
The hose nozzle
Water flows at 0.80 m/s through a hose with an inside diameter of 4.0 cm. It leaves through a nozzle with an opening 1.0 cm across. (a) Find the volume flow rate. (b) Find the speed of the water leaving the nozzle. (c) How long does it take to fill a 10 L bucket?
  1. (a) Hose area: $A_1 = \pi r^2 = \pi(0.020\ \text{m})^2 = 1.26 \times 10^{-3}\ \text{m}^2$. Flow rate: $A_1v_1 = (1.26 \times 10^{-3})(0.80) = 1.0 \times 10^{-3}\ \text{m}^3/\text{s}$, about 1.0 L per second.
    Why?
    Use the radius (2.0 cm = 0.020 m), not the diameter.
  2. (b) The diameter shrinks by a factor of 4, so the area shrinks by $4^2 = 16$. Continuity: $v_2 = v_1\frac{A_1}{A_2} = (0.80)(16) = 12.8\ \text{m/s}$, about 13 m/s.
    Why?
    Ratio reasoning with squares is quicker than computing both areas, and less error prone.
  3. (c) $10\ \text{L} = 1.0 \times 10^{-2}\ \text{m}^3$. Time = volume ÷ flow rate $= \frac{1.0 \times 10^{-2}}{1.0 \times 10^{-3}} = 10\ \text{s}$.
    Why?
    The nozzle doesn't change the flow rate in this model, only the speed. It fills the bucket no faster.

Answer: (a) About $1.0 \times 10^{-3}\ \text{m}^3/\text{s}$ (1 L/s). (b) About 13 m/s. (c) About 10 s.

Stuck? Get a hint
  1. Area from radius: $\pi r^2$, in m².
  2. Diameter ÷ 4 means area ÷ 16.
  3. Time = volume ÷ volume flow rate.
Check yourself
Water flows steadily through a pipe whose diameter triples from one section to the next. Compared with the narrow section, the speed in the wide section is
  1. A3 times as fast
  2. Bthe same
  3. C1/3 as fast
  4. D1/9 as fast
Show the answer

D. Triple the diameter means $3^2 = 9$ times the area, and continuity ($Av$ constant) means one ninth the speed. Choosing 1/3 uses the diameter as if it were the area, the classic slip.

  • Volume flow rate: $Av$, in m³/s. The same at every cross section of a pipe in steady flow.
  • Continuity: $A_1v_1 = A_2v_2$. It is conservation of mass for an incompressible fluid.
  • Narrow: fast. Wide: slow. Area goes with diameter squared.