AP Physics 1 · Unit 5 lecture · Part 4 of 11 · 8 min

5.3 TorqueHow hard a force twists

Mr. Thompkins
Try this tonight: push a door open with one finger at the handle, then push near the hinges. Same push, completely different result. The difference has a name: torque.

A force can make an object spin, but only if it pushes off-center. How well a force twists depends on three things: how big the force is, how far from the axis it acts, and its angle. Torque, $\tau$ (tau), puts all three together: $\tau = rF\sin\theta$, where $r$ is the distance from the axis to the point where the force acts, and $\theta$ is the angle between the line from the axis to that point and the force. The unit is the newton meter, N·m.

?Wait, what does $\sin\theta$ do here?
Sine picks out the part of the force that's perpendicular to the radius line. $\sin 90° = 1$, so a perpendicular push counts fully. $\sin 0° = 0$, so a push straight along the radius, toward or away from the axis, counts not at all. In between, $\sin 30° = 0.50$ counts half.
bolt (axis)$r$ = 0.30 m90°: 15 N·m30°: 7.5 N·m0°: 0each force: 50 N, applied at the end
Three 50 N pushes on the end of a 0.30 m wrench. Only the perpendicular part of each force twists. A push along the handle does nothing.

With $r = 0.30$ m and $F = 50$ N: the perpendicular push gives $\tau = (0.30)(50)(1) = 15$ N·m. The push at 30° to the handle gives $(0.30)(50)(0.50) = 7.5$ N·m. The push straight along the handle gives zero. And any force whose line passes right through the axis gives zero torque, however big it is. That's why the force from a hinge or an axle never twists the object it holds.

The lever arm

There's a second way to read the same formula, and it's often faster. Extend the force into a line, its line of action. The lever arm (or moment arm), $r_\perp$, is the perpendicular distance from the axis to that line. Then $\tau = r_\perp F$. Geometrically $r_\perp = r\sin\theta$, so it's the same torque. Use whichever is easier to see in the picture.

hinge$r$ = 0.80 m$F$ = 40 N60°$r_\perp$ = 0.69 mline of actionseen from above
A 40 N pull at the edge of a door, at 60° to the door. The lever arm is the perpendicular distance from the hinge to the force's line of action.
?Wait, how do I find a perpendicular distance?
Draw the line of the force, extended as far as you need. Then from the axis, draw the shortest segment to that line: it meets the line at a right angle. That segment's length is the lever arm. In a right triangle with hypotenuse $r$, it's the side opposite the angle $\theta$, so it's $r\sin\theta$.

Torque has a direction too: it tends to turn the object counterclockwise or clockwise. In AP Physics 1, call counterclockwise positive and clockwise negative, and decide the sign of each torque by imagining that force acting alone on the object, starting from rest. Which way would it turn?

Pause and think
A mechanic can't loosen a stuck bolt. Give two changes that increase her torque without pushing any harder.
I thought about it. Show me
Push farther from the bolt (a longer wrench, or slide a pipe over the handle), which increases $r$. And push perpendicular to the handle, which makes $\sin\theta = 1$. Both increase $\tau = rF\sin\theta$ with the same $F$.
Calculate a torque two ways
A person pulls on the edge of a 0.80 m wide door with a 40 N force at 60° to the door's surface, as shown. Find the torque about the hinge (a) using $\tau = rF\sin\theta$ and (b) using the lever arm.
  1. (a) $r = 0.80$ m, $F = 40$ N, and the angle between the door and the force is 60°. $\tau = (0.80)(40)\sin 60° = 27.7$ N·m.
    Why?
    The angle between the force and the line along the door is 60°. sin 60° = sin 120°, so it doesn't matter which side of the door you measure from.
  2. (b) Lever arm: $r_\perp = r\sin 60° = (0.80)(0.866) = 0.69$ m. $\tau = r_\perp F = (0.69)(40) = 27.7$ N·m.
    Why?
    Same answer, as it must be. Keep unrounded values until the end.
  3. Compare with pushing perpendicular at the edge: $(0.80)(40) = 32$ N·m, the most this force can give here.

Answer: About 28 N·m (27.7 N·m), whichever method you use.

Stuck? Get a hint
  1. Find r: the distance from the hinge to where the force acts.
  2. The angle between the door and the force is 60°, so use $\sin 60° = 0.866$.
  3. $\tau = (0.80)(40)(0.866)$.
Check yourself
A 20 N force acts 0.50 m from an axis. Which angle between the radius line and the force gives a torque of 5.0 N·m?
  1. A0°
  2. B30°
  3. C60°
  4. D90°
Show the answer

B. $\tau = rF\sin\theta$: $5.0 = (0.50)(20)\sin\theta = 10\sin\theta$, so $\sin\theta = 0.50$ and $\theta = 30°$. At 90° the torque would be 10 N·m, the maximum; at 0° it would be zero.

  • Torque $\tau = rF\sin\theta = r_\perp F$, in N·m. Only the perpendicular part of the force twists.
  • A force through the axis, or along the radius line, makes zero torque.
  • Lever arm: the perpendicular distance from the axis to the line of action of the force.
  • Counterclockwise positive, clockwise negative: imagine each force acting alone.