AP Physics C: Mechanics · Unit 2 lecture · Part 6 of 11 · 9 min

2.7 Kinetic and static frictionFriction: the force that adjusts

Mr. Thompkins
Push on a heavy couch. At first nothing happens. Push harder, still nothing. Then suddenly it breaks loose and slides, and keeping it moving is easier than starting it was. That little story contains everything about friction.

Friction is the part of the contact force from a surface that acts along the surface. It comes in two kinds. Static friction acts when the surfaces are not sliding against each other. It adjusts to whatever is needed to prevent sliding, up to a maximum: $f_s \le \mu_sF_N$. Kinetic friction acts when they are sliding. It has a fixed size, $f_k = \mu_kF_N$, and points opposite the sliding.

The coefficients $\mu_s$ and $\mu_k$ are numbers with no units that depend on the two surfaces. Usually $\mu_k < \mu_s$, which is why the couch is easier to keep moving. In this model, friction doesn't depend on the contact area or (for kinetic friction) on the speed.

?Wait, why does friction exist at all?
Even polished surfaces are rough at the microscopic scale. Where the tiny bumps touch, the atoms of the two surfaces attract and lock together. Static friction is those contacts holding. Kinetic friction is them breaking and re-forming as the surfaces slide. Press the surfaces together harder and more contacts form, which is why friction grows with the normal force.
0255075100125150020406080100120applied push (N)friction (N)$\mu_sF_N = 98$ N$\mu_kF_N = 68.6$ Nstatic: matches push
A 20 kg box with μs = 0.50 and μk = 0.35. Static friction matches the push up to 98 N. Past that, the box slides and friction drops to 68.6 N.
?Wait, is the normal force always $mg$?
Only on a level surface with no other vertical forces. On an incline it's $mg\cos\theta$. Pushing down on a box increases it, and pulling up at an angle decreases it. Find $F_N$ from the perpendicular direction of your FBD every time, then multiply by $\mu$.
Pause and think
The box in the graph is pushed with 50 N and doesn't move. How big is the static friction force on it?
I thought about it. Show me
50 N. Static friction is exactly what's needed to keep it at rest, here balancing the push. It is not $\mu_sF_N = 98\ \text{N}$. That's only the maximum, reached when the box is just about to slip.
$mg$$F_N$$f_s$
A block on an incline tilted until it is just about to slip. Static friction points up the slope and has reached its maximum.
The angle where it slips
A block sits on a board, and you slowly tilt the board. The coefficients are $\mu_s = 0.50$ and $\mu_k = 0.35$. (a) At what angle does the block start to slide? (b) Once it slides, if you hold the board at that angle, what is its acceleration?
  1. (a) Along the slope, at the verge of slipping: $mg\sin\theta = f_{s,max} = \mu_sF_N$. Perpendicular: $F_N = mg\cos\theta$.
    Why?
    The verge of slipping is the one moment when static friction equals μs $F_N$. That is what makes the inequality an equation.
  2. So $mg\sin\theta = \mu_smg\cos\theta$, which gives $\tan\theta = \mu_s = 0.50$ and $\theta = 26.6°$.
    Why?
    The mass cancels. Any block of this material slips at the same angle, a nice way to measure μs in a lab.
  3. (b) Now it slides, so friction is kinetic: $ma = mg\sin\theta - \mu_kmg\cos\theta$.
    Why?
    Down the slope is positive. Kinetic friction points up the slope, against the sliding.
  4. $a = 9.8(\sin 26.6° - 0.35\cos 26.6°) = 9.8(0.447 - 0.313) = 1.3\ \text{m/s}^2$ down the slope.

Answer: (a) 26.6° (b) about 1.3 m/s² down the slope

Stuck? Get a hint
  1. At the verge of slipping, $f_s$ = μs $F_N$, and $F_N$ = mg cos θ.
  2. Divide: tan θ = μs.
  3. Once sliding, switch to μk and write ma = mg sin θ − μk mg cos θ.
Check yourself
A block rests on an incline at angle θ without sliding. Which expression gives the static friction force on it?
  1. A$\mu_smg\cos\theta$
  2. B$mg\sin\theta$
  3. C$mg\cos\theta$
  4. D$\mu_kmg\cos\theta$
Show the answer

B. At rest, static friction balances the component of gravity along the slope: $f_s = mg\sin\theta$. Choice A is the maximum possible static friction, which is the answer only at the verge of slipping. The question didn't say that.

Exam tip from Mr. T

When an FRQ says "just begins to slip" or "on the verge of sliding", write $f_s = \mu_sF_N$. When it says "at rest" with no such phrase, write $f_s$ as an unknown and find it from $\sum F = 0$. Using $\mu_sF_N$ when the object isn't about to slip is one of the most common lost points in this unit.

  • Static: $f_s \le \mu_sF_N$, as big as needed to prevent sliding. Kinetic: $f_k = \mu_kF_N$, against the sliding.
  • Find $F_N$ from the perpendicular direction. It changes with angles and extra pushes.
  • On the verge of slipping on an incline: $\tan\theta = \mu_s$.
  • Sliding down a rough incline: $a = g(\sin\theta - \mu_k\cos\theta)$.