AP Physics 1 · Unit 6 lecture · Part 4 of 11 · 7 min

6.3 Angular impulseTorque times time

Mr. Thompkins
Impulse changed linear momentum. You can probably guess what changes angular momentum. Let's make sure you can use it on a graph.

Start from Newton's second law for rotation: $\Sigma\tau = I\alpha = I\dfrac{\Delta\omega}{\Delta t} = \dfrac{\Delta L}{\Delta t}$. So the net torque is the rate of change of angular momentum. Multiply by $\Delta t$: the angular impulse $\tau\Delta t$ equals the change in angular momentum, $\tau\Delta t = \Delta L$. When the torque varies, the angular impulse is the area under a torque-time graph.

?Wait, what was the impulse-momentum theorem?
From Unit 4: the impulse on an object, $F\Delta t$ (the area under a force-time graph), equals its change in momentum, $\Delta p$. A bigger force or a longer time gives a bigger change.
00.10.20.30.40.502468101214t (s)$\tau$ (N·m)area = $\Delta L$ = 2.4 kg·m²/s
A short torque pulse on a wheel. The area under the torque-time graph is the change in angular momentum.

Read the pulse: a triangle with a 0.40 s base and a 12 N·m peak has area $\tfrac12(0.40)(12) = 2.4$ kg·m²/s. If the wheel has $I = 0.30$ kg·m² and starts at rest, it ends up at $\omega = 2.4/0.30 = 8.0$ rad/s.

The flip side: on a graph of angular momentum against time, the slope is the net torque. A straight rising line means a constant torque. A flat line means zero net torque, so the angular momentum is constant.

01234050100150200t (s)$L$ (kg·m²/s)slope = 90 N·mslope 0: no torque
Angular momentum of a merry-go-round being pushed. The slope is the net torque: 90 N·m during the push, zero afterward.
Pause and think
Two kids give a merry-go-round the same push for the same time, one at the rim and one halfway to the center. Who gives the bigger angular impulse?
I thought about it. Show me
The kid at the rim. Same force and time, but twice the lever arm, so twice the torque and twice the angular impulse $\tau\Delta t$.
Push a merry-go-round
A playground merry-go-round with its riders has $I = 450$ kg·m² and starts at rest. A parent pushes tangentially on the rim, 1.5 m from the axle, with a 60 N force for 2.0 s. Ignore friction. (a) Find the angular impulse. (b) Find the final angular velocity. (c) Sketch the $L$-$t$ graph in words.
  1. (a) Torque: $\tau = r_\perp F = (1.5)(60) = 90$ N·m. Angular impulse: $\tau\Delta t = (90)(2.0) = 180$ kg·m²/s.
    Why?
    Tangential means perpendicular to the radius, so the lever arm is the full 1.5 m.
  2. (b) $\Delta L = I\Delta\omega$, so $\omega = \dfrac{180}{450} = 0.40$ rad/s.
  3. (c) A straight line rising from 0 to 180 kg·m²/s over 2.0 s (slope 90 N·m), then flat after the push ends.
    Why?
    That's exactly the graph above. Flat means no net torque, not no motion.

Answer: (a) 180 kg·m²/s. (b) 0.40 rad/s. (c) Rising line to 180, then horizontal.

Stuck? Get a hint
  1. Torque first: $r_\perp F$.
  2. Angular impulse $= \tau\Delta t$.
  3. Divide by $I$ for $\Delta\omega$.
Check yourself
A torque-time graph for a wheel is a rectangle: 4.0 N·m for 0.50 s. The wheel has $I = 0.25$ kg·m² and was spinning at 2.0 rad/s in the same direction as the torque. What is its final angular velocity?
  1. A8.0 rad/s
  2. B10 rad/s
  3. C2.5 rad/s
  4. D4.0 rad/s
Show the answer

B. $\Delta L = (4.0)(0.50) = 2.0$ kg·m²/s, so $\Delta\omega = 2.0/0.25 = 8.0$ rad/s. Add it to the starting 2.0 rad/s: 10 rad/s. 8.0 rad/s forgets the wheel was already spinning.

  • Angular impulse $\tau\Delta t = \Delta L$; with a varying torque, it's the area under τ-t.
  • $\Sigma\tau = \Delta L/\Delta t$: the slope of an L-t graph is the net torque.
  • Final angular momentum = initial angular momentum + angular impulse.