AP Physics 1 · Unit 2 lecture · Part 8 of 11 · 9 min

2.5 and 2.7 on an inclineRamps: tilt your axes

Mr. Thompkins
Ramps scare people because everything's at an angle. Here's the secret: tilt your axes so one runs along the ramp and one runs perpendicular to it. Then only gravity is at an angle, and you split it once.

On a ramp tilted at angle $\theta$, the object moves along the surface, so choose $x$ along the ramp and $y$ perpendicular to it. The normal force is already along $y$, friction is already along $x$, and the only force you have to split is gravity. Its component along the ramp (pulling the object down the slope) is $mg\sin\theta$. Its component into the ramp is $mg\cos\theta$.

$mg$$mg\sin\theta$$mg\cos\theta$$\theta$ = 30°tilted axes: along andperpendicular to the ramp
Gravity on a 30° ramp split along tilted axes: mg sin θ down the slope and mg cos θ into the ramp.
?Wait, why is it sine along the ramp and not cosine?
Check a limiting case. On a flat ramp, $\theta = 0$, nothing should pull the object along it: $\sin 0 = 0$. Good. On a vertical "ramp", $\theta = 90°$, gravity is all along the surface: $\sin 90° = 1$. Good. The angle between the gravity arrow and the "into the ramp" axis equals the ramp angle $\theta$, so the into-the-ramp part uses cosine.

With nothing else pressing on the object, the perpendicular direction has no acceleration, so $F_N = mg\cos\theta$. That's less than $mg$, and it shrinks as the ramp gets steeper. On a frictionless ramp, the only force along the slope is $mg\sin\theta$, so $a = g\sin\theta$. The mass cancels, just as in free fall: a frictionless ramp is "slowed-down free fall".

$F_g$$F_N$$f_k$
A 4.0 kg block sliding down a 30° ramp with friction: gravity straight down, the normal force perpendicular to the ramp, and kinetic friction up the slope, against the sliding.
Sliding down a rough ramp
A 4.0 kg block slides down a 30° ramp with $\mu_k = 0.20$. Find its acceleration.
$F_g$$F_N$$f_k$
  1. Axes: $x$ down the slope (the way it accelerates), $y$ perpendicular to the ramp. Forces: $F_g$, $F_N$, and $f_k$ up the slope.
    Why?
    It slides down, so kinetic friction points up the slope.
  2. Perpendicular: $F_N - mg\cos 30° = 0$, so $F_N = (4.0)(9.8)(0.866) = 33.9$ N, and $f_k = (0.20)(33.9) = 6.79$ N.
  3. Along the slope: $mg\sin 30° - f_k = ma$, so $a = \frac{19.6 - 6.79}{4.0} = 3.20\ \text{m/s}^2$.
    Why?
    In symbols, $a = g(\sin\theta - \mu_k\cos\theta)$. The mass cancels, so any block of the same material slides with the same acceleration.

Answer: About 3.2 m/s² down the ramp.

Stuck? Get a hint
  1. Tilt your axes: along and perpendicular to the ramp.
  2. Perpendicular balance gives $F_N = mg\cos\theta$.
  3. Along the ramp: $mg\sin\theta - \mu_k mg\cos\theta = ma$.
01530456075900246810ramp angle (°)a down the ramp (m/s²)frictionless$\mu_k$ = 0.2030°: 3.20
Acceleration down a ramp against its angle. Frictionless (blue): g sin θ. With μk = 0.20 (red): smaller, and below about 11° the block would not keep sliding at all.
Pause and think
A box rests on a board. You slowly tilt the board up. At what angle does the box start to slide, if $\mu_s = 0.60$?
I thought about it. Show me
It slides when the pull down the slope beats maximum static friction: $mg\sin\theta > \mu_s mg\cos\theta$, which means $\tan\theta > \mu_s$. So $\theta = \tan^{-1}(0.60) = 31°$. The mass cancels again, and this is a neat way to measure $\mu_s$ in a lab: just find the angle where things start to slip.
?Wait, why does $\frac{\sin\theta}{\cos\theta}$ become $\tan\theta$?
By definition, $\tan\theta = \frac{\sin\theta}{\cos\theta}$. So dividing both sides of $\sin\theta = \mu_s\cos\theta$ by $\cos\theta$ gives $\tan\theta = \mu_s$.
Check yourself
A crate rests on a ramp. The ramp is made steeper, but the crate still does not slide. What happens to the normal force and the static friction force on the crate?
  1. ANormal force increases; friction increases.
  2. BNormal force decreases; friction increases.
  3. CNormal force decreases; friction decreases.
  4. DBoth stay the same.
Show the answer

B. $F_N = mg\cos\theta$ shrinks as $\theta$ grows. Static friction must balance $mg\sin\theta$, which grows. Choice C assumes friction follows the normal force, but static friction is "whatever is needed", not $\mu_s F_N$.

Exam tip from Mr. T

On ramp diagrams, draw gravity straight down, not perpendicular to the ramp. Then write the components in your equations. Drawing $F_g$ tilted is one of the most common lost points on the exam.

  • Tilt your axes: x along the ramp, y perpendicular. Only gravity needs splitting.
  • Along the ramp: $mg\sin\theta$. Into the ramp: $mg\cos\theta$. With no other perpendicular forces, $F_N = mg\cos\theta$.
  • Frictionless: $a = g\sin\theta$. Sliding with friction: $a = g(\sin\theta - \mu_k\cos\theta)$ going down.
  • A resting object starts to slip when $\tan\theta = \mu_s$.