AP Physics 1 · Unit 2 lecture · Part 1 of 11 · 8 min

2.1 Systems and center of massPick your system first

By the end: Choose a system, draw a correct free-body diagram, and use Newton's three laws with gravity, normal, tension, friction and spring forces to predict and explain motion in a line, on a ramp, and in a circle, the way AP free-response questions are scored.
Mr. Thompkins
Welcome to Unit 2, the biggest unit on the exam. In Unit 1 we described motion. Now we ask why it changes. The answer is forces, and every force problem starts with one small decision that most students skip: what exactly am I looking at?

A system is the object or group of objects you decide to study. Everything else is the environment. You draw the line, and that choice is yours. It might be one block, two blocks tied together, a person and the elevator, or a car and its passengers. The physics doesn't change with your choice, but how easy the problem is can change a lot.

Once you pick a system, every force sorts itself into one of two bins. An internal force is exerted by one part of the system on another part. An external force is exerted on the system by something outside it. Internal forces always come in equal and opposite pairs inside the system (you'll see why in Section 3), so they cancel when you add up the forces on the whole system. Only external forces can change how the system as a whole moves.

ABhand: externalA on B, B on A: internalsystem: A + Boutside the dashed line:hand, Earth, floor
A hand pushes cart A, which pushes cart B. With the system drawn around both carts, the push between A and B is internal and drops out. The hand, Earth and the floor are outside, so their forces are external.
?Wait, what's a force, exactly?
A force is a push or a pull that one object exerts on another. It's an interaction between two objects, so every force has an object that exerts it and an object it acts on. Forces are vectors, measured in newtons (N). One newton is about the weight of a small apple.

"How the system as a whole moves" has a precise meaning: it's the motion of the center of mass. The center of mass is the average position of the system's mass, weighted by how much mass is where. For objects along a line, $x_{cm} = \frac{\Sigma m_i x_i}{\Sigma m_i}$. A system moves as if all its mass sat at that one point and all the external forces acted there.

?Wait, what's a weighted average?
A weighted average counts some values more than others. If you score 90 on a test worth 3 points of your grade and 60 on a quiz worth 1 point, your weighted average is $\frac{3(90) + 1(60)}{4} = 82.5$, closer to the test score. In the center of mass formula, mass is the weight, so the center of mass sits closer to the heavier objects.
5.0 kg2.0 kgcenter of mass0.00.40.81.21.62.0x (m)0.80 m
A 5.0 kg ball at 0.40 m and a 2.0 kg ball at 1.80 m on a light rod. The center of mass is at 0.80 m, much closer to the heavier ball.
Find the center of mass
A light rod holds a 5.0 kg ball at $x = 0.40$ m and a 2.0 kg ball at $x = 1.80$ m. Where is the center of mass of the system?
5.0 kg2.0 kgcenter of mass0.00.40.81.21.62.0x (m)0.80 m
  1. Write the definition: $x_{cm} = \frac{m_1 x_1 + m_2 x_2}{m_1 + m_2}$.
    Why?
    Start from the definition in symbols. It is on the equation sheet, and graders like to see it.
  2. Substitute: $x_{cm} = \frac{(5.0)(0.40) + (2.0)(1.80)}{5.0 + 2.0} = \frac{2.0 + 3.6}{7.0}$.
  3. $x_{cm} = \frac{5.6}{7.0} = 0.80$ m.
    Why?
    Sanity check: the answer must lie between the two balls, and closer to the 5.0 kg one. 0.80 m does both.

Answer: $x_{cm} = 0.80$ m, between the balls and closer to the heavier one.

Stuck? Get a hint
  1. Multiply each mass by its position.
  2. Add those products, then divide by the total mass, 7.0 kg.
  3. $\frac{2.0 + 3.6}{7.0}$.
Pause and think
A high jumper arches her back over the bar so that her body curves around it. Can her center of mass pass under the bar while every part of her body goes over it?
I thought about it. Show me
Yes. For a curved shape the center of mass can sit outside the object, like the center of a ring. When she arches around the bar, her center of mass can pass just below it. That's why the arched technique lets jumpers clear higher bars for the same launch.

Two more facts the course expects. For a symmetric object with mass spread evenly, like a uniform ball, ring or rod, the center of mass is at the geometric center. And if the net external force on a system is zero, its center of mass keeps a constant velocity, no matter what the parts do to each other. Two skaters pushing off each other fly apart, but their center of mass stays put.

Check yourself
Two carts are joined by a compressed spring and held at rest on a frictionless track. The spring is released and the carts fly apart. For the system of both carts and the spring, what happens to the center of mass?
  1. AIt moves toward the heavier cart.
  2. BIt moves toward the lighter cart.
  3. CIt stays at rest.
  4. DIt speeds up while the spring pushes, then moves at constant speed.
Show the answer

C. The spring forces are internal to the system, and the track is frictionless, so the net external horizontal force is zero. The center of mass started at rest, so it stays at rest. Choice D treats the spring push as if it were external.

Exam tip from Mr. T

On free-response, write the system in words: "System: both blocks." Then list which forces are external. When the question changes the system in a later part, the grader can follow you, and you will not accidentally include an internal force.

  • A system is whatever you choose to study. Forces from inside it are internal; forces from outside are external.
  • Internal forces cancel in pairs. Only external forces change the motion of the system's center of mass.
  • Center of mass: $x_{cm} = \frac{\Sigma m_i x_i}{\Sigma m_i}$. It sits closer to the heavier parts and can be outside the object.
  • Zero net external force: the center of mass moves with constant velocity (or stays at rest).