8.5 Electric fluxFlux: how much field passes through a surface

For a flat surface of area A in a uniform field, the electric flux is
$$\Phi_E = EA\cos\theta = \vec E\cdot\vec A$$
where θ is the angle between $\vec E$ and the surface's normal, the direction perpendicular to the surface. The area vector $\vec A$ has size A and points along that normal. Flux has units N·m²/C.
?Wait, what's a dot product again?
?Wait, what's a normal, exactly?
If the field isn't uniform, or the surface is curved, chop the surface into tiny patches $d\vec A$ and add: $\Phi_E = \int \vec E\cdot d\vec A$. For a closed surface (one with an inside and an outside, like a balloon), the normal always points outward. Then flux is positive where field lines leave and negative where they enter. The net flux through a closed surface is written with a circle on the integral: $\oint \vec E\cdot d\vec A$.
I thought about it. Show me
- (a) $\Phi = EA\cos\theta = (500)(0.20)\cos 30° = 86.6\ \text{N·m}^2/\text{C}$.
- (b) If the field is 30° from the surface, it's 60° from the normal.
Why?
The normal is perpendicular to the surface, so the two angles add to 90°. - $\Phi = (500)(0.20)\cos 60° = 50\ \text{N·m}^2/\text{C}$.
Answer: (a) $87\ \text{N·m}^2/\text{C}$. (b) $50\ \text{N·m}^2/\text{C}$.
Stuck? Get a hint
- θ always goes between E and the normal.
- 30° from the surface means 60° from the normal.
- Then Φ = EA cos θ.
- The four faces parallel to the x-axis have normals perpendicular to $\hat i$, so $\vec E\cdot d\vec A = 0$ on them.
- Face at $x = 0$: $E = 0$ there, so its flux is 0.
- Face at $x = a$: $E = ba$ is uniform over that face and points along its outward normal, so $\Phi = (ba)(a^2) = ba^3 = (400)(0.50)^3 = 50\ \text{N·m}^2/\text{C}$.
- (b) $q_{enc} = \varepsilon_0\Phi = (8.85 \times 10^{-12})(50) = 4.4 \times 10^{-10}$ C.
Why?
More field leaves than enters, so there must be positive charge inside creating the extra field.
Answer: (a) $50\ \text{N·m}^2/\text{C}$. (b) $4.4 \times 10^{-10}$ C, about 0.44 nC.
Stuck? Get a hint
- On which faces is E parallel to the surface? Their flux is zero.
- On the face at x = a, E has the same value everywhere: E = ba.
- Flux there is E times the face area a².
- A$2\pi R^2E$
- B$\pi R^2E$
- C$4\pi R^2E$
- D0
Show the answer
B. The dome and the flat base form a closed surface with no charge inside, so their fluxes cancel. The base catches $-E\pi R^2$ (field entering), so the dome has $+\pi R^2E$. $2\pi R^2E$ uses the dome's area, but most of the dome is tilted to the field.
- Flat surface, uniform field: $\Phi_E = EA\cos\theta$, θ measured from the normal.
- General: $\Phi_E = \int\vec E\cdot d\vec A$. Closed surface: normals point outward.
- Leaving field: positive flux. Entering field: negative flux. Parallel to the surface: zero.
- A uniform field through a closed surface gives zero net flux.