AP Physics 1 · Unit 6 lecture · Part 2 of 11 · 8 min

6.2 Torque and workTwisting through an angle

Mr. Thompkins
In Unit 3, a force did work by pushing through a distance. A torque does work by twisting through an angle. Same energy bookkeeping, new letters.
?Wait, how did work work in Unit 3?
Work is a force acting through a displacement: $W = F_\parallel d$, using only the part of the force along the motion. The work-energy theorem says the net work on an object equals its change in kinetic energy: $W_{net} = \Delta K$. Work is in joules.

Picture a force $F$ pushing tangentially on the rim of a wheel of radius $r$ while the wheel turns through $\Delta\theta$. The rim point moves a distance $r\Delta\theta$, so the work is $F(r\Delta\theta) = (rF)\Delta\theta = \tau\Delta\theta$. That's the rule: the work done by a constant torque is $W = \tau\Delta\theta$, with $\Delta\theta$ in radians. If the torque is in the same direction as the rotation, the work is positive and adds energy. If it opposes the rotation, like friction in a bearing, the work is negative and removes energy.

And the work-energy theorem carries over: the net work done by all the torques on a rigid object equals its change in rotational kinetic energy, $\Sigma W = \Delta K_{rot}$. When the torque changes as the object turns, the work is the area under a graph of torque against angle, just as work was the area under a force-position graph.

0246810120123456$\theta$ (rad)$\tau$ (N·m)area = work = 40 J
Torque on a wheel against the angle it turns. The area under the graph is the work done: a 30 J rectangle plus a 10 J triangle.
?Wait, why must the angle be in radians?
The step $s = r\Delta\theta$ only works with radians, and $W = \tau\Delta\theta$ came from it. If you're given revolutions, multiply by $2\pi$ first. Using degrees would give a work 57 times too big.

Read the graph: 5.0 N·m for the first 6.0 rad gives 30 J, and the falling part from 6.0 to 10 rad adds $\tfrac12(4.0)(5.0) = 10$ J. Total work: 40 J. If this torque is the only one acting on a wheel with $I = 0.20$ kg·m² starting from rest, then $\tfrac12(0.20)\omega^2 = 40$, so $\omega = 20$ rad/s.

Pause and think
A torque acts on a wheel but the wheel is held so it can't turn. How much work does the torque do?
I thought about it. Show me
Zero. Work needs an angle turned: $W = \tau\Delta\theta$ and $\Delta\theta = 0$. Just like pushing on a wall that doesn't move does no work, however tired you get.
Stop a wheel with friction
A bicycle wheel on a stand has $I = 0.20$ kg·m² and spins at 12 rad/s. A brake pad applies a constant friction torque of 0.80 N·m. (a) How much work does the brake do to stop the wheel? (b) Through what angle does the wheel turn while stopping? (c) Where does the energy go?
  1. (a) Work-energy theorem: $W = \Delta K_{rot} = 0 - \tfrac12(0.20)(12)^2 = -14.4$ J.
    Why?
    The brake opposes the rotation, so its work is negative.
  2. (b) $W = -\tau\Delta\theta$, so $\Delta\theta = \dfrac{14.4}{0.80} = 18$ rad, about 2.9 revolutions.
    Why?
    Check with kinematics: α = −0.80/0.20 = −4.0 rad/s², and Δθ = ω₀²/(2|α|) = 144/8.0 = 18 rad. ✓
  3. (c) The 14.4 J becomes internal energy: the brake pad and the rim warm up.
    Why?
    Energy is conserved for the whole system; friction moves it from kinetic to internal.

Answer: (a) −14.4 J. (b) 18 rad, about 2.9 rev. (c) Internal energy of the pad and rim.

Stuck? Get a hint
  1. Find the starting kinetic energy: $\tfrac12I\omega^2$.
  2. All of it has to be removed by the brake.
  3. $\Delta\theta = $ (energy removed) ÷ (torque).
Spinning (J)14.4$K_{rot}$$\Delta E_{int}$Stopped (J)$K_{rot}$14.4$\Delta E_{int}$
Energy bar charts for the braking wheel. All 14.4 J of rotational kinetic energy becomes internal energy.
Check yourself
A constant torque of 3.0 N·m turns a wheel through 2.0 revolutions. How much work does it do?
  1. A6.0 J
  2. B12 J
  3. C38 J
  4. D1,100 J
Show the answer

C. Convert first: 2.0 rev = $4\pi$ rad ≈ 12.6 rad. $W = (3.0)(12.6) = 38$ J. 6.0 J uses revolutions as if they were radians, and 1,100 J uses 720°.

  • Work by a torque: $W = \tau\Delta\theta$ (radians). Positive if the torque is along the rotation, negative if against it.
  • Rotational work-energy theorem: $\Sigma W = \Delta K_{rot}$.
  • Work is the area under a torque-angle graph.
  • Friction torque turns rotational kinetic energy into internal energy.